[PE1] display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 12 Routes : 12
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 Direct 0 0 D 127.0.0.1 InLoopBack0
2.2.2.9/32 OSPF 10 1 D 172.1.1.2 Vlanif30
3.3.3.9/32 OSPF 10 2 D 172.1.1.2 Vlanif30
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.1.1.0/24 Direct 0 0 D 172.1.1.1 Vlanif30
172.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.1.1.2/32 Direct 0 0 D 172.1.1.2 Vlanif30
172.1.1.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.2.1.0/24 OSPF 10 2 D 172.1.1.2 Vlanif30
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
[PE1] display ospf peer
OSPF Process 1 with Router ID 1.1.1.9
Neighbors
Area 0.0.0.0 interface 172.1.1.1(Vlanif30)'s neighbors
Router ID: 172.1.1.2 Address: 172.1.1.2
State: Full Mode:Nbr is Master Priority: 1
DR: None BDR: None MTU: 1500
Dead timer due in 37 sec
Neighbor is up for 00:16:21
Authentication Sequence: [ 0 ]
Step 2 Configure basic MPLS functions and MPLS LDP on the MPLS backbone network and set up
LDP LSPs.
# Configure PE1.
[PE1] mpls lsr-id 1.1.1.9
[PE1] mpls
[PE1-mpls] quit
[PE1] mpls ldp
[PE1-mpls-ldp] quit
[PE1] interface vlanif 30
[PE1-Vlanif30] mpls
[PE1-Vlanif30] mpls ldp
[PE1-Vlanif30] quit
# Configure the P.
[P] mpls lsr-id 2.2.2.9
[P] mpls
[P-mpls] quit
[P] mpls ldp
[P-mpls-ldp] quit
[P] interface vlanif 30
[P-Vlanif30] mpls
[P-Vlanif30] mpls ldp
[P-Vlanif30] quit
[P] interface vlanif 60
[P-Vlanif60] mpls
[P-Vlanif60] mpls ldp
[P-Vlanif60] quit
# Configure PE2.
[PE2] mpls lsr-id 3.3.3.9
[PE2] mpls
[PE2-mpls] quit
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 3 BGP MPLS IP VPN Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
177
To Next Page
Loading...
