[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit
# Configure the P.
<Quidway> system-view
[Quidway] sysname P
[P] interface loopback 1
[P-LoopBack1] ip address 2.2.2.9 32
[P-LoopBack1] quit
[P] vlan batch 30 60
[P] interface gigabitethernet 1/0/0
[P-GigabitEthernet1/0/0] port hybrid pvid vlan 30
[P-GigabitEthernet1/0/0] port hybrid untagged vlan 30
[P-GigabitEthernet1/0/0] quit
[P] interface gigabitethernet 2/0/0
[P-GigabitEthernet2/0/0] port hybrid pvid vlan 60
[P-GigabitEthernet2/0/0] port hybrid untagged vlan 60
[P-GigabitEthernet2/0/0] quit
[P] interface vlanif 30
[P-Vlanif30] ip address 172.1.1.2 24
[P-Vlanif30] quit
[P] interface vlanif 60
[P-Vlanif60] ip address 172.2.1.1 24
[P-Vlanif60] quit
[P] ospf
[P-ospf-1] area 0
[P-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[P-ospf-1-area-0.0.0.0] quit
[P-ospf-1] quit
# Configure PE2.
<Quidway> system-view
[Quidway] sysname PE2
[PE2] interface loopback 1
[PE2-LoopBack1] ip address 3.3.3.9 32
[PE2-LoopBack1] quit
[PE2] vlan batch 40 50 60
[PE2] interface gigabitethernet 1/0/0
[PE2-GigabitEthernet1/0/0] port hybrid pvid vlan 40
[PE2-GigabitEthernet1/0/0] port hybrid untagged vlan 40
[PE2-GigabitEthernet1/0/0] quit
[PE2] interface gigabitethernet 2/0/0
[PE2-GigabitEthernet2/0/0] port hybrid pvid vlan 50
[PE2-GigabitEthernet2/0/0] port hybrid untagged vlan 50
[PE2-GigabitEthernet2/0/0] quit
[PE2] interface gigabitethernet 3/0/0
[PE2-GigabitEthernet3/0/0] port hybrid pvid vlan 60
[PE2-GigabitEthernet3/0/0] port hybrid untagged vlan 60
[PE2-GigabitEthernet3/0/0] quit
[PE2] interface vlanif 60
[PE2-Vlanif60] ip address 172.2.1.2 24
[PE2-Vlanif60] quit
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
After the configuration, OSPF adjacencies are established between PE1, P, and PE2. By running
the display ospf peer command, you can see that the status of the OSPF adjacency is Full. By
running the display ip routing-table command, you can see that the PEs can learn the routes
of each other's Loopback1 interface.
Take PE1 for example.
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 3 BGP MPLS IP VPN Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
176
To Next Page
Loading...
