Why is the Intermec Label Maker printout weaker on one side?
If the printout from your Intermec Label Maker is weaker on one side, this is likely due to uneven printhead pressure. You should adjust the arm alignment.
How to fix transfer ribbon wrinkles on Intermec Label Maker?
Transfer ribbon wrinkles on your Intermec Label Maker can be caused by faulty ribbon break shaft adjustment, incorrect edge guide adjustment, or too strong print-head pressure. Try to adjust these settings.
How to fix printout missing along inner edge on Intermec Label Maker?
If the printout is missing along the inner edge on your Intermec Label Maker, it could be due to bad media alignment, a small core & supply post in the upper position, or an X-start parameter value that is too low. Adjust the media alignment, move the post to the lower position, or increase the X-start parameter value.
What to do if Intermec EasyCoder PM4i Printer has wrong media type parameter?
If the media type parameter is wrong on your Intermec printer, change the parameter, then clean the printhead.
What to do if Intermec EasyCoder PM4i has worn platen roller?
If your Intermec printer has a worn platen roller, check or replace it.
What to do if Intermec EasyCoder PM4i Printer has faulty energy control?
If your Intermec printer has a faulty energy control, replace the CPU board or call service.
What to do if Intermec EasyCoder PM4i Printer has failing strobe signal?
If your Intermec printer has a failing strobe signal, check the CPU-board.
General| Print technology | Direct thermal |
|---|---|
| Maximum resolution | 203 x 203 DPI |
| Display | LCD |
| Product color | Silver |
| Standard interfaces | RS-232, USB 2.0 |
| Internal memory | 16 MB |
| Media thickness | 2.5/8.7 mm |
| Maximum label width | 114.3 mm |
| Maximum label length | 4 m |
| Maximum roll diameter | 213 mm |
| Maximum internal memory | 1 GB |
| Supported network protocols | TCP/IP, LPR/LPD, FTP, BOOTP, DHCP, HTTP, SNMPv3, SMTP, SNMP-MIB II |
| Power requirements | 90 - 265 VAC, 45 - 65Hz |
| Power consumption (standby) | 15 W |
| Power consumption (printing) | 125 W |
| Storage temperature (T-T) | -20 - 70 °C |
| Operating temperature (T-T) | 40 - 104 °F |
| Operating relative humidity (H-H) | 20 - 80 % |
Weight and Dimensions| Depth | 543 mm |
|---|---|
| Width | 298 mm |
| Height | 261 mm |
| Weight | 13500 g |
Provides essential safety warnings and precautions for operating Intermec equipment.
Explains the meaning of various warning and caution icons used in the document.
Details warranty information and how to access web and telephone support.
Lists services and contact options for technical support and product ordering.
Identifies the target audience and lists how to download or order additional Intermec documentation.
Details the specifications, features, and capabilities of the EasyCoder PM4i printer.
Summarizes critical safety warnings and how to identify the printer's model and serial number.
Describes the components and features visible on the front panel of the printer.
Details the connectors, switches, and slots located on the rear panel of the printer.
Explains the media compartment, supply roll post, and print mechanism for loading and printing.
Explains how to connect the printer to power and a computer via various interfaces.
Introduces the printer's interface elements like indicator lamps, display, keyboard, and beeper.
Explains startup files, memory card usage, and printer behavior on power-on.
Provides a step-by-step guide on how to power on the printer and its initialization process.
Describes common media loading methods like Tear-Off, Peel-Off, and Cut-Off.
Explains loading media using external supplies like fanfolds or rotating hubs.
Guides the user on how to load the thermal transfer ribbon correctly for printing.
Details how to enter and navigate Setup Mode, and configure parameters via Fingerprint/Direct Protocol.
Controls communication parameters for serial ports, including baud rate, parity, and flow control.
Configures media feed adjustments and media characteristics for optimal print quality.
Sets print speed, tests, and sensor adjustments for print quality.
Provides methods to reset all printer setup parameters to their original factory defaults.
Explains how to enter and navigate the printer's Setup Mode using the keyboard and display.
Introduces Intermec Shell, how to start it, and select applications or facilities.
Details the Line Analyzer program for diagnosing communication problems by capturing and printing data.
Describes how adding options enhances the printer's flexibility for various applications.
Details options like liner takeup, paper cutter, media hubs, sensors, and retainers for media management.
Covers options for keyboards, RFID kits, printheads, and various interface boards.
Explains the IRI status and lists error messages with their meanings for troubleshooting.
Provides a guide to common print quality symptoms, their possible causes, and suggested remedies.
Details printhead cleaning and cleaning the media guides for optimal print quality and longevity.
Explains safe external cleaning and procedures for clearing media jams.
Provides instructions on how to safely replace the printer's printhead.
Guides on adjusting for narrow media and aligning the Label Stop Sensor (LSS).
Explains how to adjust printhead pressure and ribbon break shaft for optimal performance.
Explains how to adjust the sensitivity of the Label Taken Sensor (LTS).
Lists technical data for printing, modes of operation, firmware, physical measures, and electronics.
Details printer controls, data interfaces, and available accessories and options.
Provides specifications for media roll sizes and details for various media types like labels and tickets.
Details the RS-232 interface protocol and pinout, and the printer's USB support.
Explains the bar code wand interface and lists optional interface boards for expanded connectivity.
Lists Intermec's direct thermal and thermal transfer media, and transfer ribbons for various applications.
Provides recommended paper type settings by region and explains bar code printing directions.
Provides detailed setup overviews for serial communication ports UART1 through UART5.
Details network communication setup for NET1 and RFID configuration options.
To Next Page
