Lenze i55AE155F - Page 675

Address Designaon Default seng Category Data type Factor A M
0x2540:004
(P208.04)
Mains sengs: Undervoltage reset threshold x V (Read only) general U16 1 - -
0x2540:005
(P208.05)
Mains sengs: Overvoltage warning threshold 0 V * general U16 1 P -
0x2540:006
(P208.06)
Mains sengs: Overvoltage error threshold x V (Read only) general U16 1 - -
0x2540:007
(P208.07)
Mains sengs: Overvoltage reset threshold x V (Read only) general U16 1 - -
0x2541:001
(P706.01)
Brake energy management: Operang mode Ramp funcon generator
stop (RFGS) [1]
general U8 1 P -
0x2541:002
(P706.02)
Brake energy management: Acve threshold x V (Read only) general U16 1 P -
0x2541:003
(P706.03)
Brake energy management: Reduced threshold 0 V general U16 1 P -
0x2541:004
(P706.04)
Brake energy management: Addional frequency 0.0 Hz general U16 10 P -
0x2541:005
(P706.05)
Brake energy management: Deceleraon override
me
2.0 s general U16 10 P -
0x2541:006
(P706.06)
Brake energy management: Brake resistor response O: disable and error [0] general U8 1 PC -
0x2550:002
(P707.02)
Brake resistor: Resistance value 180.0 Ω * general U16 10 P -
0x2550:003
(P707.03)
Brake resistor: Rated power 50 W * general U32 1 P -
0x2550:004
(P707.04)
Brake resistor: Maximum thermal load 8.0 kWs * general U32 10 P -
0x2550:007
(P707.07)
Brake resistor: Thermal load x.x % (Read only) general U16 10 - -
0x2550:008
(P707.08)
Brake resistor: Warning threshold 90.0 % general U16 10 P -
0x2550:009
(P707.09)
Brake resistor: Error threshold 100.0 % general U16 10 P -
0x2550:010
(P707.10)
Brake resistor: Response to warning Warning [1] general U8 1 P -
0x2550:011
(P707.11)
Brake resistor: Response to error Fault [3] general U8 1 P -
0x2552:002
(P595.02)
Parameter access monitoring: Keep alive register 0 general U16 1 K -
0x2552:003
(P595.03)
Parameter access monitoring: Time-out me 10.0 s general U16 10 P -
0x2552:004
(P595.04)
Parameter access monitoring: Reacon No response [0] general U8 1 P -
0x2552:005
(P595.05)
Parameter access monitoring: Acon No acon [0] general U8 1 P -
0x2552:006
(P595.06)
Parameter access monitoring: Parameter Access
Monitoring-Status
- (Read only) general U16 1 - -
0x2552:007
(P595.07)
Parameter access monitoring: WLAN reset me-out
me
0 s general U16 1 P -
0x2601:001
(P202.01)
Keypad setpoints: Frequency setpoint 20.0 Hz general U16 10 P r
0x2601:002
(P202.02)
Keypad setpoints: Process controller setpoint 0.00 PID unit general I16 100 P r
0x2601:003
(P202.03)
Keypad setpoints: Torque setpoint 100.0 % general I16 10 P r
0x2602:001
(P708.01)
Keypad setup: CTRL & F/R key setup CTRL & F/R Enable [1] general U8 1 P -
0x2602:002
(P708.02)
Keypad setup: Select rotaonal direcon Forward [0] general U8 1 P -
* Default seng depending on the size. Firmware version 05.00.00.00
Appendix
Parameter aribute list
675