Lenze i55AE155F

Address Designaon Default seng Category Data type Factor A M
0x402B:005
(P806.05)
Sequencer segment 6: Analog outputs 0.00 VDC general U16 100 P -
0x402B:006
(P806.06)
Sequencer segment 6: PID setpoint 0.00 PID unit general I16 100 P -
0x402B:007
(P806.07)
Sequencer segment 6: Torque setpoint 100.0 % general I16 10 P -
0x402B:008 Sequencer segment 6: NetWordOUT2 0 general U16 1 P -
0x402B:009 Sequencer segment 6: Reserved 0 general U32 1 P -
0x402C:001
(P807.01)
Sequencer segment 7: Frequency setpoint 0.0 Hz general I16 10 P -
0x402C:002
(P807.02)
Sequencer segment 7: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x402C:003
(P807.03)
Sequencer segment 7: Time 0.0 s general U32 10 P -
0x402C:004
(P807.04)
Sequencer segment 7: Digital outputs 0 general U8 1 P -
0x402C:005
(P807.05)
Sequencer segment 7: Analog outputs 0.00 VDC general U16 100 P -
0x402C:006
(P807.06)
Sequencer segment 7: PID setpoint 0.00 PID unit general I16 100 P -
0x402C:007
(P807.07)
Sequencer segment 7: Torque setpoint 100.0 % general I16 10 P -
0x402C:008 Sequencer segment 7: NetWordOUT2 0 general U16 1 P -
0x402C:009 Sequencer segment 7: Reserved 0 general U32 1 P -
0x402D:001
(P808.01)
Sequencer segment 8: Frequency setpoint 0.0 Hz general I16 10 P -
0x402D:002
(P808.02)
Sequencer segment 8: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x402D:003
(P808.03)
Sequencer segment 8: Time 0.0 s general U32 10 P -
0x402D:004
(P808.04)
Sequencer segment 8: Digital outputs 0 general U8 1 P -
0x402D:005
(P808.05)
Sequencer segment 8: Analog outputs 0.00 VDC general U16 100 P -
0x402D:006
(P808.06)
Sequencer segment 8: PID setpoint 0.00 PID unit general I16 100 P -
0x402D:007
(P808.07)
Sequencer segment 8: Torque setpoint 100.0 % general I16 10 P -
0x402D:008 Sequencer segment 8: NetWordOUT2 0 general U16 1 P -
0x402D:009 Sequencer segment 8: Reserved 0 general U32 1 P -
0x402E:001
(P822.01)
End segment: Frequency setpoint 0.0 Hz general I16 10 P -
0x402E:002
(P822.02)
End segment: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x402E:003
(P822.03)
End segment: Time 0.0 s general U32 10 P -
0x402E:004
(P822.04)
End segment: Digital outputs 0 general U8 1 P -
0x402E:005
(P822.05)
End segment: Analog outputs 0.00 VDC general U16 100 P -
0x402E:006
(P822.06)
End segment: PID setpoint 0.00 PID unit general I16 100 P -
0x402E:007
(P822.07)
End segment: Torque setpoint 100.0 % general I16 10 P -
0x402E:008 End segment: NetWordOUT2 0 general U16 1 P -
0x402E:009 End segment: Reserved 0 general U32 1 P -
0x402F
(P824.00)
End of sequence mode Keep running [0] general U8 1 P -
* Default seng depending on the size. Firmware version 05.00.00.00
Appendix
Parameter aribute list
698