Chapter 4 Settings — [PICTURE] menu
110 - ENGLISH
[OFF] Disables the dynamic contrast function.
[1] Adjusts the light source and compensates signals to a small extent.
[2] Adjusts the light source and compensates signals to a moderate extent.
[3] Adjusts the light source and compensates signals to a large extent.
[USER]
Set any desired correction.
Refer to “Performing desired correction” (x page 110) for details.
Performing desired correction
1) Press as to select [DYNAMIC CONTRAST].
2) Press qw or the <ENTER> button.
f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.
3) Press qw to select [USER].
4) Press the <ENTER> button.
f The [DYNAMIC CONTRAST] screen is displayed.
5) Press as to select the item to set.
f The items of the detailed settings will switch each time you press qw.
f Press the <ENTER> button when [MULTI PROJECTOR SYNC] is selected.
Setting item Details
[AUTO CONTRAST]
(Automatic light source
adjustment)
[OFF] Does not adjust the light source.
[1] - [255]
The higher the value, the stronger the light adjustment of the light
source.
Can be set in increments of 1.
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness level
of the signal to start the light
adjustment)
[6%] - [50%]
Adjusts the light source when the brightness level of the video
signal being input gets lower than the set value. The higher the
value, the larger the range to perform the light adjustment of the
light source.
Can be set in increments of 1 %. (Factory setting: 30 %)
[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[DISABLE] Does not turn off the light source.
[0.0s] - [10.0s]
Turns off the light source when the brightness level of the video
signal being input goes under the value set in [LIGHTS OUT
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] -
[4.0s] can be selected in increments of 0.5.
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[0%] - [5%]
Set the level of the brightness of the video signal to turn off the light
source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
[LIGHTS OUT FADE-IN]
(Setting of fade-in when lighting
up again)
[OFF]
Does not set the fade-in of the image when the light source is
turned on again from the condition that the light source was turned
off with [LIGHTS OUT TIMER].
[0.5s] - [10.0s]
Sets the time to fade in the image when the light source is turned
on again from the condition that the light source was turned off with
[LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[OFF]
Does not set the fade-out of the image when the light source is
turned off with [LIGHTS OUT TIMER].
[0.5s] - [10.0s]
Sets the time to fade out the image when the light source is turned
off with [LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
[MANUAL INTENSITY]
(Manual light source
adjustment)
[0] - [255]
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[OFF] Does not compensate the signal.
[1] Slightly compensates the signal.
[2] Moderately compensates the signal.
[3] Strongly compensates the signal.
To Next Page
Loading...
