Panasonic DLP PT-RZ34K

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 189
5) Press as to select the input to be specified as the switching destination, and press the <ENTER>
button.
[OFF] Disables the secondary input switching function.
[HDMI] Sets the secondary input to HDMI.
[DVI-D] Sets the secondary input to DVI-D.
[SDI] Sets the secondary input to SDI.
[DIGITAL LINK] Sets the secondary input to DIGITAL LINK
*1
.
[HDMI1 [SLOT]]
*2
Sets the secondary input to HDMI1 of the Interface Board.
[HDMI2 [SLOT]]
*2
Sets the secondary input to HDMI2 of the Interface Board.
[DVI-D1 [SLOT]]
*2
Sets the secondary input to DVI-D1 of the Interface Board.
[DVI-D2 [SLOT]]
*2
Sets the secondary input to DVI-D2 of the Interface Board.
[DisplayPort1 [SLOT]]
*2
Sets the secondary input to DisplayPort1 of the Interface Board.
[DisplayPort2 [SLOT]]
*2
Sets the secondary input to DisplayPort2 of the Interface Board.
[SDI1 [SLOT]]
*2
Sets the secondary input to SDI1 of the Interface Board.
[SDI2 [SLOT]]
*2
Sets the secondary input to SDI2 of the Interface Board.
[SDI3 [SLOT]]
*2
Sets the secondary input to SDI3 of the Interface Board.
[SDI4 [SLOT]]
*2
Sets the secondary input to SDI4 of the Interface Board.
[SDI OPT1 [SLOT]]
*2
Sets the secondary input to SDI OPT1 of the Interface Board.
[SDI OPT2 [SLOT]]
*2
Sets the secondary input to SDI OPT2 of the Interface Board.
*1 Individual input on the twisted-pair-cable transmitter or the DIGITAL LINK output supported device cannot be specied.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT>.
Note
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set to
anything other than [OFF], the secondary input switching function will not operate even when [SECONDARY INPUT] is set to anything other
than [OFF]. The backup input switching function is prioritized.
[BACK COLOR]
Set the display of the screen when a signal is not input.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [BACK COLOR].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[BLUE] Displays blue in the entire screen.
[BLACK] Displays black in the entire screen.
[DEFAULT LOGO] Displays the Panasonic logo in the screen.
[USER LOGO] Displays the image registered by the user in the screen.
Note
f The [BACK COLOR] setting item is common with the following menu item.
g The [DISPLAY OPTION] menu → [BACK COLOR]
f To create and register the [USER LOGO] image, use “Logo Transfer Software”. The software can be downloaded from the Panasonic
website (https://panasonic.net/cns/projector/).
When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for “NO
SIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn off the light source of the projector when there is no input signal for specic
period. The time until the light source is turned off can be set.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.