Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 193
5) Press as to select a command number, and press the <ENTER> button.
f You can change the page using qw.
6) Press asqw to select [TIME], and press the <ENTER> button.
f The projector is in the adjustment mode (the time is blinking).
7) Press qw to select “hour” or “minute”, and press as or the number (<0> - <9>) buttons to set a
time, and then press the <ENTER> button.
8) Press asqw to select [COMMAND].
9) Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to be
set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON] ― Switches on the projector.
[STANDBY] ― Enters standby.
[SHUTTER]
[OPEN] Disables the shutter function (shutter: opened).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT]
[HDMI] Switches the input to HDMI.
[DVI-D] Switches the input to DVI-D.
[SDI] Switches the input to SDI.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[HDMI1 [SLOT]]
*1
Switches the input to HDMI1 of the Interface Board.
[HDMI2 [SLOT]]
*1
Switches the input to HDMI2 of the Interface Board.
[DVI-D1 [SLOT]]
*1
Switches the input to DVI-D1 of the Interface Board.
[DVI-D2 [SLOT]]
*1
Switches the input to DVI-D2 of the Interface Board.
[DisplayPort1 [SLOT]]
*1
Switches the input to DisplayPort1 of the Interface Board.
[DisplayPort2 [SLOT]]
*1
Switches the input to DisplayPort2 of the Interface Board.
[SDI1 [SLOT]]
*1
Switches the input to SDI1 of the Interface Board.
[SDI2 [SLOT]]
*1
Switches the input to SDI2 of the Interface Board.
[SDI3 [SLOT]]
*1
Switches the input to SDI3 of the Interface Board.
[SDI4 [SLOT]]
*1
Switches the input to SDI4 of the Interface Board.
[SDI OPT1 [SLOT]]
*1
Switches the input to SDI OPT1 of the Interface Board.
[SDI OPT2 [SLOT]]
*1
Switches the input to SDI OPT2 of the Interface Board.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[OPERATING MODE]
*3
[NORMAL] Prioritizes brightness.
[ECO] Prioritizes the life of the light source.
[QUIET] Prioritizes the operation with low noise.
[USER1] Controls the power with the setting set to [USER1].
[USER2] Controls the power with the setting set to [USER2].
[USER3] Controls the power with the setting set to [USER3].
*1 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT>.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
*3 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <ENTER> button.
f The command is xed and n is displayed at the left of the selected command.
f After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
To Next Page
Loading...
