Chapter 1 Preparation — About your projector
36 - ENGLISH
Interface Board for 12G-SDI (Model No.: ET-MDN12G10)
This board supports the HD-SDI signal, the 3G-SDI signal, the 6G-SDI signal, and the 12G-SDI signal.
25 541 3
1 <SDI 1 IN> terminal
This is a terminal to input SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI).
2 <SDI 2 IN/1 OUT> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 1 IN>
terminal of this board.
3 <SDI 3 IN> terminal
This is a terminal to input SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI).
4 <SDI 4 IN/3 OUT> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 3 IN>
terminal of this board.
5 Handle
Note
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu → [SLOT
IN] → [SDI MODE] to [OUTPUT].
f When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
Interface Board for 12G-SDI Optical (Model No.: ET-MDNFB10)
24 41 3
1 SFP port 1
This is the port to install the SFP module for receiving.
2 SFP port 2
This is the port to install the SFP module for sending and
receiving.
3 Input indicator <SIGNAL>
This is the indicator to indicate the detection state of the video
signal. This is illuminated when input of the video signal is
detected in either or both of the <SDI OPT 1 IN> terminal and
the <SDI OPT 2 IN> terminal.
4 Handle
Note
f The sending function of the SFP module for sending or for sending and receiving will not operate when it is installed in the SFP port 1.
f In addition to the SFP module for sending and receiving, the SFP module for receiving or for sending can be installed in the SFP port 2.
r When the SFP modules are installed
This is an example when the SFP module for receiving (LC connector) is installed in the SFP port 1, and the SFP
module for sending and receiving (LC connector) is installed in the SFP port 2.
21 1
1 <SDI OPT 1 IN> terminal/<SDI OPT 2 IN> terminal
These are terminals to input SDI signal (optical signal).
2 <SDI OPT 1/2 OUT> terminal
This is an active through terminal to output the signal input to
the <SDI OPT 1 IN> terminal/<SDI OPT 2 IN> terminal.
Note
f The input signal to the <SDI OPT 1 IN> terminal or the <SDI OPT 2 IN> terminal that is selected for input is output from the <SDI OPT 1/2
OUT> terminal.
To Next Page
Loading...
