Parker EME
Compax3 Accessories
I11 T11 192-120101 N6 - March 2004 113
8.3.2.1 Motor data table for standard motors
Motor type
Standstill
torque
Nominal
current
Resistan
ce
Inductan
ce
Torque
constant
Moment of
inertial*
Mains
voltage
Nominal
speed
Nominal
torque
Nominal
current
Nominal
output
Type
M
0
I
0
Ω
ΩΩ
Ω
mH K
T
JU n
n
M
n
I
n
P
n
Order code
Nm A Nm/A kgmm
2
Vrpms NmA
eff
kW
1.4 1.7 11.4 32.3 0.81 30.2/42.8 230 3300 1.18 1.46 0.484
SMH 60 ...
60 1.4 8 9 2ID 65 400: flange 60; shaft 9
70 1.4 5 11 2ID 65 400: flange 60; shaft 11
400 6000 1.12 1.40 0.880
3.0 3.5 3.38 18.2 0.85 140/183 230 3300 2.4 2.8 0.829
SMH 82 ...
60 03 8 14 2ID 65 400: flange 82; shaft 14
60 03 5 19 2ID 65 400: flange 100; shaft 19
400 6000 1.36 1.6 0.855
SMH 100 ...
6.0 5.9 1.12 11.2 1.02 336/440 230 3000 4.70 4.6 1.477
56 06 5 19 2ID 65 400: flange 100; shaft 19
400 5600 1.64 1.61 3.520
MH 105 ...
3.95 2.57 6.69 24.79 1.65 335/398 230 1600 4.00 2.50 0.660
30 04 9 19 2I 65 400: flange 96; shaft 19
400 3000 3.49 2.23 1.097
60 04 9 19 2I 65 400: flange 96; shaft 19
3.98 5.01 1.80 6.61 0.85 335/398 230 3000 3.60 4.40 1.115
400 6000 2.40 3.02 1.510
45 06 6 24 2I 65 400: flange 116; shaft 24
5.96 5.60 1.83 7.93 1.14 480/543 230 2500 5.50 5.00 1.434
400 4500 4.06 3.79 1.918
45 08 5 19 2I 65 400: flange 105; shaft 19
45 08 6 24 2I 65 400: flange 116; shaft 24
7.97 7.47 1.29 5.95 1.14 620/683 400 4500 5.24 4.89 2.473
30 08 6 24 2I 65 M 400: flange 116; shaft 24
8.01 5.21 2.63 12.39 1.65 760/822 230 1600 7.8 5.00 1.306
400 3000 6.80 4.35 2.137
MH 145 ... 8.72 5.51 1.93 19.27 1.70 1050/1245 230 1600 8.60 5.20 1.430
30 08 5 24 3I 65 400: flange 145; shaft 24
400 3000 7.84 4.84 2.464
20 15 5 24 3I 65 M 400: flange 145; shaft 24
15.00 6.20 1.64 14.38 2.59 1600/1795 230 1100 14.70 5.90 1.665
400 2000 14.19 5.73 2.966
45 15 5 24 3I 65 400: flange 145; shaft 24
15.01 14.17 0.316 2.77 1.13 1600/1795 400 4500 10.47 9.69 4.934
30 22 5 24 3I 65 400: flange 145; shaft 24
22.01 13.12 0.474 3.77 1.80 2150/2345 400 3000 17.76 10.35 5.577
20 28 5 24 3I 65 400: flange 145; shaft 24
27.99 11.33 0.678 5.44 2.65 2700/2895 400 2000 25.21 9.95 5.169
MH 205 ...
20 28 5 38 3I 65 400: flange 205; shaft 38
27.96 12.99 0.932 8.87 2.31 5000/6000 400 2000 27.25 12.32 5.704
20 50 5 38 3I 65 400: flange 205; shaft 38
50.31 22.08 0.372 4.95 2.45 8000/9000 400 2000 46.95 20.07 9.829
20 70 5 38 3I 65 400: flange 205; shaft 38
69.99 30.72 0.215 3.30 2.44 11000/12000 400 2000 62.87 26.89 13.161
20 90 5 38 3I 65 400: flange 205; shaft 38
89.63 44.26 0.117 2.25 2.17 14000/15000 400 2000 78.33 37.71 16.372
* Without / with motor holding brake
Boundary conditions of the motor data table
! Tolerance +/-10%.
! Over-temperature 65K with 20°C ambient temperature.
! Twice the rated torque is possible up to 90% of the rated rotation speed.
! Three times the rated torque is possible up to 80% of the rated rotation speed.
! Data applies to: motor freely mounted and with flange plate size: up to 2Nm:
200*230*20; up to 35Nm 200*270*20; >35Nm: 310*320*25 in mm.
In addition, we offer an extensive range of rotary and linear direct drives!
We will be happy to process your request!
To Next Page
Loading...
Need help?
General
