FX-20
• Do not fly in any way, which could endanger humans or ani-
mals.
• Never fly close to high-tension overhead cables or residen-
tial areas.
• Don’t operate your model in the vicinity of canals, locks or
other public waterways.
• You must not operate your model from public roads, motor-
ways, paths, squares etc.
Never operate your equipment in stormy weather.
Don’t “point” the transmitter aerial straight at the aeroplane
when flying. The signal generated by the transmitter is at its
weakest in an imaginary line extending straight from the aerial.
It is always best for the pilot to stand in a position where the
long side of the aerial points towards the model.
INSURANCE
Ground-based models are usually covered by standard per-
sonal third-party insurance policies. To fly powered model air-
craft you will need to extend the cover of your existing policy,
or take out a specific policy. Check your insurance and take
out new cover where necessary.
1. CONTENTS
Contents: FX-20 2,4 GHz NO. F 8072
1 FX-20 G 2,4 GHz FASST transmitter
1 7,2 V 3400 mAh LiPo transmitter battery
1 R-6108 SB 2,4 GHz FASST receiver
1 Switch harness with charge socket
1 12 V Lithium battery charger, 2 A
1 110 ... 230 V AC switch-mode PSU, for charging the main
supply
RECOMMENDED ACCESSORIES:
Trainer cord FF9 > FF9 No. F1591
Trainer special cord No. F1314
Flight simulator adapter lead FF9 No. 8239
Charge lead T8 FG No. 8260
Receiver battery 4.8V 1400 mAh No. 4551
Spare Tx battery LiPo 7.2V 3400 mAh No. 4846
Wireless Trainer System No. F1414
Rx charge lead No. F1416
Transmitter case No. F9906
Ali. Case for tray Tx No. 8899
Stick switch FX-20 No. 8051 - 8053
Joystick short No. F1526
Neck strap mounting FX-30 No. 8384
Neck strap mounting FX-30 + hand rast No. 8381
Senderpult FX-30 CFK No. 8491
2. GENERAL DESCRIPTION
With the FX-20 system the range of robbe Futaba console
transmitters is extended downwards, so permitting a low-cost
entry point to 2.4 GHz technology.<br/><li>The FASST system
is a Spread Spectrum System with Frequency Hopping (FHSS).
2.1 FX-20 TRANSMITTER
• The FASST system is a Spread Spectrum system with Fre-
quency Hopping (FHSS). It is therefore permitted to trans-
mit a maximum power of 100 mW EIRP. This gives it ade-
quate reserve even for large-scale model aircraft and jets.
• Maximum security from same-channel interference, vir-
tually interference-free and insensitive to electrical smog.
• Focal point of the transmitter is the large, high resolution
128 x 64 Dot graphic display with backlighting for excellent
readability.
• The elegant and clean design of the system is created using
the new Cap-Touch-System. A contact-free capacitive sen-
sor that will function like a 3D Hotkey. It has a smooth, non-
porous display with no protruding user controls.
• Easy programming using the graphics driven user interface,
the menu structure and operation are largely the same as
the FX30 systems, genauso wie das moderne und prakti-
sche Gehäuse Design
• The software is in 8 languages: English, german, french,
Italian, Spanish, Czech, Russian or Dutch.
• The joystick coupling mechanism has twin ball bearings
and is designed for Universal mode. They can be easily
converted from „throttle left“ to „throttle right“ by the owner.
• The FX-20 transmitter features the new rotary stick trim-
ming. This type of trimming combines the advantages of tra-
ditional analogue trims with those of digital trimming. With
just one movement, the direction and size of trim required
will be set and automatically stored.
• The linear slider controls are very practical to use for auxili-
ary control functions such as gyros, flaps or speed control-
lers.
• The system consists of ten channels (8 proportional and 2
switched) and these are all freely assignable.
• The transmitter is supplied fully equipped with 2 analogue
rotary, 2 linear slide controls and 6 switches.
• Comprehensive software provides all the essential facilities
and extensive functionality for power models, gliders and
helicopters.
• Plenty of freely programmable mixers are available with a
choice of 5-point curves for setting up very complex mixer
functions.
• Integrated Trainer system with individual control func-
tion transfer. Freely configurable channel assignment for
instructor and student.
• using an SD card, the owner can update the software to the
latest version.
• Twenty internal model memories, with infinite expansion
using SD card-3862 models= 2GB.
4
General
To Next Page
Loading...