ROBBE FX-20 - Exponential (Expo) Curve Settings; Set Exponential (Expo) Curve

92 pages

Save Page as PDF

To Next Page

To Previous Page

FX-20

11. Set Expo

Select a switch to

changeover between

the different control

curve settings.

Define first control

curve, switch position 1:

Programming example

2 x

Main Page

Default Chapter2
- Table of Contents2
- Stick Mode Selection2
  - Set Delay Time3
Safety Precautions, Observe at All Times 1. Contents4
- R-6108 SB Receiver5
- Receiver Binding5
- Connecting the Servo Using PWM6
- Receiver Output Configuration for Aircraft8
- FX-20 Transmitter9
- Receiver R6108 SB 2,4 Ghz9
2 General Descripton4
- Ailvator (2 Elevator With Aileron) Function4
- Power Down Mode Range Testing4
3 Technical Data9
- Transmitter9
4 Transmitter Controls9
- LED Monitor10
- Liquid Crystal Display10
- Stick Adjustment10
  - Length Adjustment10
  - Spring Centring10
- Turning Transmitter on and off10
- Changing Throttle Function11
- Digital Trim Buttons11
- Ratchet Activation (Stick Mode)11
- Aerial12
- Linear Slider12
- Rotary Control Knobs12
- Sd Card Memory12
5 Remove/Change the Transmitter Battery13
6 RC Charger, Charging the Trasmitter Battery14
7 Menus and Navigation15
- Home Screen/ Start Display for All Model Types16
8 Start Display Description16
- Control/Switch H/W SELECT Menu17
- Timer18
9 System Menu (Sys)19
- TRAINER Operation19
- Trainer System20
  - Trainer As Instructor Tx20
  - Trainer As Student Tx21
- Display Settings21
- Flight Simulator Operation21
- Control Set-Up H/W SET22
- Switch - Switchtyp Assigment22
- User Name22
- Information23
10 Linkage Menu (LNK)23
- Servo23
- Model Select24
- Model Type25
  - Select Wing And Tail Type26
  - Select Swashplate Type26
- Change Frequency Area27
- Frequency Modulation Mode Fasst27
  - 7Chanel / Mult27
- Function28
- Sub Trim Servo Centring29
- Fail Safe Adjustment30
- Servo Reverse30
- Servo End Point/Travel Adjust31
- Thr Cut Function31
- Idle Down Preset Throttle Position32
- T1-T4 Trim Adjust32
  - Trim Memory32
- Data Reset33
- Warning33
- Flight Condition (Glider Only)34
  - Copy Flight Condition35
  - Change Priorities35
11 MODEL (MDL) MENU (Airplane)34
- Servo34
- Dual Rate (Arf/Expo)35
- Programmable Mixer36
- Aileron Differential37
- Throttle Curve/ Thr Delay (Power Airplanes Only)37
- Aileron -> Camber Flap Mixer38
- Flaps Settings38
- Aileron -> Brake Flap Mixer39
- Aileron -> Rudder Mixer39
- Spoiler -> Flap (Camber MIX)39
- Elevator -> Camber Mixer40
- Camber Flap -> Elevator Mixer41
- Rudder -> Aileron Mixer41
- Crow/ Butterfly Mixer42
- Gyro Settings43
- Trim MIX43
- V-Tail Mixer44
- Winglet Rudder Settings44
- Electric Motor Settings45
- Rudder -> Elevator Mixer45
- Airbrake Mixer46
- Snap Roll Function46
- Fuel Mixxture Adjustment47
12 LINKAGE Menu-Helicopter48
- Rx Outputs For Helicopter Models48
- Function49
- Swash Ring51
  - Swashplate Settings51
- Flight Condition (Idle Up)52
  - Copy Flight Condition53
  - Change Priorities53
13 Heli Model Menü52
- Pitch Curve Settings53
- Throttle Curve Settings55
- Swash Mixer56
- Thr Hold/ Autorotation Settings56
- Gyro Settings57
- Pitch -> Rud (Revo) MIX57
- Throttle MIX57
- Governor Settings58
- Fuel Mixture Settings59
14 Programming Example for FX-20 Tx60
15 Tx Software Update82
16 Installation and Aerial Positioning of 2,4 Ghz FASST Rx83
- Interference Suppression Filter85
- Servo Installation85
- Servo Leads85
- Switch Harness85
- Brushed Electric Motors86
- Linkage Installation86
- Metal To Metal Interference86
17 Operational Advice86
- Servo Travel And Arms86
- Switch On Sequence86
18 Guarantee87
19 Liability Exclusions87
- Rx Battery Capacity/Operating Time87
20 Homologation87
21 Declaration of Conformity87
- Electronic Ignitions87
22 Compliance Information Statement88
23 Accessories89
24 Service Addresses91
25 End of Life Disposal92

ROBBE FX-20 - Exponential (Expo) Curve Settings; Set Exponential (Expo) Curve

Table of Contents

Related product manuals