Roland VR-6HD

104
Menu List
Menu item Value (bold text: default value) Explanation
USB IN Adjusts the audio that is input from the USB STREAM connector.
DIGITAL GAIN -42.0–0.0–42.0dB Adjusts the digital gain.
INPUT LEVEL -INF–0.0–10.0dB Adjusts the input volume.
INPUT MUTE OFF, ON Turns the mute function on/o. When this is “ON”, the input audio is temporarily silenced.
MONO
Converts the input audio from stereo to mono.
OFF Sends the stereo input audio without change.
L ONLY The audio of the L channel is sent to both L and R.
R ONLY The audio of the R channel is sent to both L and R.
LR Mix The audio of the L channel and R channel is mixed, and sent to both L and R.
SOLO OFF, ON
Turns the solo function on/o. Only the audio for which this is “ON” is heard in the
headphones.
* The solo function applies to the headphone output. It does not aect output other than the
headphones.
DELAY
0.0–500msec
(0–25.0/29.9/30.0frame)
Adjusts the delay time of the audio.
Eect Outputs audio with a delay.
REVERB SEND 0–127 Adjusts the amount of audio sent to reverb.
MAIN BUS
This congures the MAIN bus.
SEND
OFF, ON When this is “ON”, audio is sent to the MAIN bus.
AUX 1 BUS
This congures the AUX 1 bus.
SEND LEVEL
-INF–10.0dB These parameters adjust the amount of audio sent to the AUX 1 bus.
SEND POINT
DRY
Sends the source audio with no eects applied.
PRE FADER
Sends the eect-applied audio.
The send volume is constant, regardless of the volume (INPUT LEVEL).
POST FADER
Sends the eect-applied audio.
The send volume can be changed by adjusting the volume (INPUT LEVEL).
AUX 2 BUS
This congures the AUX 2 bus.
SEND LEVEL
-INF–10.0dB These parameters adjust the amount of audio sent to the AUX 2 bus.
SEND POINT
DRY
Sends the source audio with no eects applied.
PRE FADER
Sends the eect-applied audio.
The send volume is constant, regardless of the volume (INPUT LEVEL).
POST FADER
Sends the eect-applied audio.
The send volume can be changed by adjusting the volume (INPUT LEVEL).
HIGH PASS FILTER 80Hz OFF, ON
Turns the high-pass lter on/o.
Eect Cuts o unneeded low-band audio. The cuto frequency is 80 Hz.
NOISE GATE OFF, ON
Turns the noise gate on/o.
Eect
Eliminates audio that is lower than the specied threshold level. This is eective when the
noise that you want to remove is separate from the audio that you want to keep, and can be
used to remove hiss or other noise that is heard during periods of silence.
THRESHOLD -80–-48–0dB
Species the level used as the threshold for removing audio. Audio below the level set
here is removed.
RELEASE 30–500–5000msec
Adjusts the length of time until the audio is fully attenuated after audio falls below the
threshold.
COMPRESSOR OFF, ON
Turns the compressor on/o.
Eect
Audio that exceeds the specied threshold level is compressed. This reduces the dierence
between the maximum volume and minimum volume, making the audio more comfortable
for listening
THRESHOLD -50–-8–0dB
Species the level used as the threshold at which the compressor is applied.
Compression is applied to audio that exceeds the threshold.
RATIO
1.00:1, 1.12:1, 1.25:1, 1.40:1,
1.60:1, 1.80:1, 2.00:1, 2.50:1,
3.20:1, 4.00:1, 5.60:1, 8.00:1,
16.0:1, INF:1
Species the degree of compression applied to the audio. The state in which no
compression is applied is dened as “1”.
ATTACK 0.0–30–100ms Species the time until compression starts when audio exceeding the threshold is input.
RELEASE 30–250–5000ms Adjusts the length of time until compression ends after audio falls below the threshold.
MAKEUP GAIN -40–0–40dB Adjusts the nal output volume level after applying the compressor.