Tektronix TDS5052 - Page 354

Index
TDS5000 Series User Manual
Index- 15
setting, 3--180
Resolution control window, D--4
RESOLUTION knob, 3--20, 3--102, 3 --104
Restore Help, D--10
Restore Help but ton, 3--210
Rise Time, B -- 2, D--7, Glossary --9
R M S , B -- 2 , D -- 7 , G l o s s a r y -- 9
Roll Mode, and ma th waveforms, 3--138
roll mode
illustrated, 3 -- 23
untriggered, 3--22
untriggered, with single sequence, 3--23
using, 3--28
Roll Mode Auto command, D--4
Roll mode, and measurements, 3--119
Run Application command, D-- 1
RUN/STOP, 3--43
Run/Stop command, D--4, D--5
RUN/STOP button, 3--22, 3--26, 3--61
Run/Stop control window, D--4, D--5
Runs After delayed trigger mode, 3--91
Runt Setup, D--5
Runt trigger, 3--62, Glossary--9
logic, 3--72
Polarity, 3 -- 71
setting up, 3-- 70
Source, 3 --70
threshold levels, 3 --72
Trigger W hen Runt, 3--72
S
Sample mode, 3 -- 21
sample interval, 3-- 19, 3--31
defined, Glossary--10
deriving, 3--20
setting, 3--11
Sample mode, defined, Glossary -- 9
sample rate
deriving, 3--20
maximum, 3-- 35
Sampling, Glossary--10
sampling, 3 -- 32
process, defined, 3--30–3--35
process, illustrated, 3--30–3--35
sampling and acquisition mode, 3-- 33
Save Instrument Setup As dialog box, 3--186
Save Instrument Setups cont rol window, 3--183
Save Wfm, D--1
saving a setup, 3--183, 3--185
saving a waveform, 3--189
saving a waveform to a reference, 3--190
scale
horizontal, D--4
vertical, D--3
SCALE knob, 3--102, 3--104
scallop loss, 3--161, 3--162
Screen saver, 3--108
Screen text, Glossary -- 10
Screen Te xt c ommand, D--6
Screen Text co mmand, 3--107
Select for Copy command, D-- 2
Select for Export, D--2
Selecting the acquisition mode, 3-- 25
selecting Zoom, 3-- 111
Sequential Triggering, 3--91
Serial num ber, D--11
Service support, contact information, xv
SetDate&Time,3--207
Set Math Averages, D--9
Setting the vertical acquisition window, 3 --10
SetTime&Date,D--10
Set Time and Date control window, D--10
Setting Acquisition Controls, 3 --21
Setting Up Signal Input, 3--8
Setting up the acquisition window, 3--14
Setting up Triggers, 3-- 54
Setting vertical range and position, 3-- 16
Setting waveform count , 3--25
Setup, dual display, 1--13
setup
adding comments, 3--183
naming, 3--186
recalling, 3--183
saving, 3--183
Setup/Hold Setup, D--5
Setup/Hold trigger, 3--65
Data Source, 3--84
negative setup or hold times, 3-- 65
positive setup or hold times, 3-- 65
setting up, 3-- 84
Trigger Inside Violation, 3 --85
trigger point location, 3--65
Setup/hold trigger
Clock Edge, 3--84
Clock Level, 3 -- 85
Clock Source, 3--84
Data Level, 3--85
Short trigger level marker, 3--108
shutdown, 1--9
Shutdown command, D--2
Side panel connectors, 2--7
Signal Connection and Conditioning, 3--4
Signal path compensation, 1--20, A--1