TP-Link T1500 Series

To Next Page

To Previous Page

Configuration Guide 714

Monitoring the System Monitoring the CPU

The following example shows how to monitor the CPU:

Switch#show cpu-utilization

Unit | CPU Utilization

No. | Five-Seconds One-Minute Five-Minutes

------+-------------------------------------------------

1 | 13% 13% 13%

Main Page

About This Guide23
- Intended Readers23
- Conventions23
- More Information24
Accessing the Switch25
- Overview26
- Web Interface Access27
- Command Line Interface Access31
Managing System41
- System42
  - Overview42
  - Supported Features42
- System Info Configurations44
  - Using the GUI44
  - Using the CLI55
- User Management Configurations66
  - Using the GUI66
    - Creating Accounts66
    - Configuring Enable Password67
  - Using the CLI68
    - Creating Accounts68
    - Configuring Enable Password70
- System Tools Configurations73
  - Using the GUI73
  - Using the CLI78
- EEE Configuration84
  - Using the CLI84
- PoE Configurations86
  - Using the GUI87
    - Configuring the PoE Parameters Manually87
    - Configuring the PoE Parameters Using the Profile90
  - Using the CLI93
    - Configuring the PoE Parameters Manually93
    - Configuring the PoE Parameters Using the Profile95
- SDM Template Configuration98
  - Using the GUI98
  - Using the CLI99
- Time Range Configuration101
  - Using the GUI101
    - Adding Time Range Entries101
    - Configuring Holiday103
  - Using the CLI104
    - Adding Time Range Entries104
    - Configuring Holiday105
- Example for PoE Configurations107
- Appendix: Default Parameters112
Managing Physical Interfaces115
- Physical Interface116
  - Overview116
  - Supported Features116
- Basic Parameters Configurations117
  - Using the GUI117
  - Using the CLI118
- Port Isolation Configurations121
  - Using the GUI121
  - Using the CLI122
- Loopback Detection Configuration124
  - Using the GUI124
  - Using the CLI126
- Configuration Examples128
  - Example for Port Isolation128
  - Example for Loopback Detection131
- Appendix: Default Parameters134
Configuring LAG135
- LAG136
  - Overview136
  - Supported Features136
- LAG Configuration137
  - Using the GUI138
    - Configuring Load-balancing Algorithm138
    - Configuring Static LAG or LACP139
  - Using the CLI141
    - Configuring Load-balancing Algorithm141
    - Configuring Static LAG or LACP142
- Configuration Example146
- Appendix: Default Parameters150
Managing MAC Address Table151
- MAC Address Table152
  - Overview152
  - Supported Features152
- MAC Address Configurations153
  - Using the GUI153
  - Using the CLI157
- Appendix: Default Parameters161
Configuring 802.1Q VLAN162
- Overview163
- 802.1Q VLAN Configuration164
  - Using the GUI164
    - Configuring the PVID of the Port164
    - Configuring the VLAN166
  - Using the CLI167
- Configuration Example171
- Appendix: Default Parameters178
Configuring MAC VLAN179
- Overview180
- MAC VLAN Configuration181
  - Using the GUI181
  - Using the CLI183
- Configuration Example185
- Appendix: Default Parameters195
Configuring Protocol VLAN196
- Overview197
- Protocol VLAN Configuration198
  - Using the GUI198
  - Using the CLI201
- Configuration Example205
- Appendix: Default Parameters217
Configuring GVRP218
- Overview219
- GVRP Configuration220
  - Using the GUI221
  - Using the CLI222
- Configuration Example225
- Appendix: Default Parameters234
Configuring Layer 2 Multicast235
- Layer 2 Multicast236
  - Overview236
  - Supported Features238
- IGMP Snooping Configuration239
  - Using the GUI239
  - Using the CLI245
- MLD Snooping Configuration255
  - Using the GUI255
  - Using the CLI260
- MVR Configuration269
  - Using the GUI269
  - Using the CLI274
- Multicast Filtering Configuration279
  - Using the GUI279
    - Creating the Multicast Profile279
    - Configure Multicast Filtering for Ports281
  - Using the CLI282
    - Creating the Multicast Profile282
    - Binding the Profile to Ports285
- Viewing Multicast Snooping Information289
  - Using the GUI289
  - Using the CLI293
    - Viewing IPv4 Multicast Snooping Information293
    - Viewing IPv6 Multicast Snooping Configurations293
- Configuration Examples294
- Appendix: Default Parameters318
Configuring Spanning Tree321
- Spanning Tree322
- STP/RSTP Configurations330
  - Using the GUI330
  - Using the CLI336
- MSTP Configurations342
  - Using the GUI342
  - Using the CLI352
- STP Security Configurations362
  - Using the GUI362
  - Using the CLI363
    - Configuring the STP Security363
- Configuration Example for MSTP366
- Appendix: Default Parameters380
Configuring LLDP382
- LLDP383
  - Overview383
  - Supported Features383
- LLDP Configurations384
  - Using the GUI384
    - Configuring LLDP Globally384
    - Configuring LLDP For the Port386
  - Using the CLI387
    - Global Config387
    - Port Config389
- LLDP-MED Configurations392
  - Using the GUI392
  - Using the CLI395
    - Global Config395
    - Port Config396
- Viewing LLDP Settings399
  - Using GUI399
    - Viewing LLDP Device Info399
    - Viewing LLDP Statistics403
  - Using CLI404
- Viewing LLDP-MED Settings405
  - Using GUI405
  - Using CLI408
- Configuration Example409
- Appendix: Default Parameters417
Configuring DHCP Service418
- DHCP419
  - Overview419
  - Supported Features419
- DHCP Relay Configuration421
  - Using the GUI421
    - Enabling DHCP Relay and Configuring Option 82421
    - Configuring DHCP VLAN Relay423
  - Using the CLI424
- DHCP L2 Relay Configuration428
  - Using the GUI428
    - Enabling DHCP L2 Relay428
    - Configuring Option 82 for Ports429
  - Using the CLI430
    - Enabling DHCP Relay430
    - Configuring Option 82 for Ports431
- Example for DHCP VLAN Relay433
- Appendix: Default Parameters440
Configuring QoS442
- QoS443
  - Overview443
  - Supported Features443
- Class of Service Configuration445
  - Using the GUI446
  - Using CLI454
- Bandwidth Control Configuration466
  - Using the GUI466
    - Configuring Rate Limit466
    - Configuring Storm Control467
  - Using the CLI468
    - Configuring Rate Limit468
    - Configuring Storm Control469
- Voice VLAN Configuration472
  - Using the GUI472
  - Using the CLI475
- Auto VoIP Configuration478
  - Using the GUI478
  - Using the CLI479
- Configuration Examples483
- Appendix: Default Parameters507
Configuring Access Security511
- Access Security512
  - Overview512
  - Supported Features512
- Access Security Configurations513
  - Using the GUI513
  - Using the CLI523
- Appendix: Default Parameters532
Configuring AAA534
- Overview535
- AAA Configuration536
  - Using the GUI537
  - Using the CLI543
- Configuration Example553
- Appendix: Default Parameters559
Configuring 802.1x561
- Overview562
- 802.1x Configuration564
  - Using the GUI564
  - Using the CLI571
- Configuration Example579
- Appendix: Default Parameters585
Configuring Port Security586
- Overview587
- Port Security Configuration588
  - Using the GUI588
  - Using the CLI589
- Appendix: Default Parameters592
Configuring ACL593
- Overview594
- ACL Configuration595
  - Using the GUI595
  - Using the CLI615
- Configuration Example for ACL627
- Appendix: Default Parameters636
Configuring IPv4 IMPB638
- IPv4 IMPB639
  - Overview639
  - Supported Features639
- IP-MAC Binding Configuration640
  - Using the GUI640
  - Using the CLI646
- ARP Detection Configuration650
  - Using the GUI650
  - Using the CLI653
- IPv4 Source Guard Configuration657
  - Using the GUI657
    - Adding IP-MAC Binding Entries657
    - Configuring IPv4 Source Guard657
  - Using the CLI658
    - Adding IP-MAC Binding Entries658
    - Configuring IPv4 Source Guard658
- Configuration Examples660
  - Example for ARP Detection660
  - Example for IP Source Guard665
- Appendix: Default Parameters668
Configuring IPv6 IMPB670
- IPv6 IMPB671
  - Overview671
  - Supported Features671
- IPv6-MAC Binding Configuration673
  - Using the GUI673
  - Using the CLI679
- ND Detection Configuration684
  - Using the GUI684
  - Using the CLI686
- IPv6 Source Guard Configuration690
  - Using the GUI690
    - Adding IPv6-MAC Binding Entries690
    - Configuring IPv6 Source Guard690
  - Using the CLI691
    - Adding IPv6-MAC Binding Entries691
    - Configuring IPv6 Source Guard691
- Configuration Examples693
  - Example for ND Detection693
  - Example for IPv6 Source Guard698
- Appendix: Default Parameters701
Configuring DHCP Filter703
- DHCP Filter704
  - Overview704
  - Supported Features704
- DHCPv4 Filter Configuration706
  - Using the GUI706
    - Configuring the Basic DHCPv4 Filter Parameters706
    - Configuring Legal DHCPv4 Servers708
  - Using the CLI708
    - Configuring the Basic DHCPv4 Filter Parameters708
    - Configuring Legal DHCPv4 Servers710
- DHCPv6 Filter Configuration712
  - Using the GUI712
    - Configuring the Basic DHCPv6 Filter Parameters712
    - Configuring Legal DHCPv6 Servers713
  - Using the CLI714
    - Configuring the Basic DHCPv6 Filter Parameters714
    - Configuring Legal DHCPv6 Servers715
- Configuration Examples717
  - Example for DHCPv4 Filter717
  - Example for DHCPv6 Filter720
- Appendix: Default Parameters725
Configuring DoS Defend726
- Overview727
- DoS Defend Configuration728
  - Using the GUI728
  - Using the CLI729
- Appendix: Default Parameters732
Monitoring the System733
- Overview734
- Monitoring the CPU735
  - Using the GUI735
  - Using the CLI735
- Monitoring the Memory737
  - Using the GUI737
  - Using the CLI737
Monitoring Traffic739
- Traffic Monitor740
  - Using the GUI740
  - Using the CLI744
- Appendix: Default Parameters745
Mirroring Traffic746
- Mirroring747
  - Using the GUI747
  - Using the CLI749
- Configuration Examples751
- Appendix: Default Parameters754
Configuring DLDP755
- Overview756
- DLDP Configuration757
  - Using the GUI757
  - Using the CLI759
- Appendix: Default Parameters761
Configuring SNMP & RMON762
- SNMP763
  - Overview763
  - Basic Concepts763
- SNMP Configurations767
  - Using the GUI767
  - Using the CLI772
- Notification Configurations780
  - Using the GUI780
    - Configuring the Information of NMS Hosts780
    - Enabling SNMP Traps782
  - Using the CLI784
    - Configuring the NMS Host784
    - Enabling SNMP Traps785
- RMON792
- RMON Configurations793
  - Using the GUI793
  - Using the CLI798
- Configuration Example805
- Appendix: Default Parameters817
Diagnosing the Device & Network821
- Diagnosing the Device822
  - Using the GUI822
  - Using the CLI823
- Diagnosing the Network824
  - Using the GUI824
    - Troubleshooting with Ping Testing824
    - Troubleshooting with Tracert Testing825
  - Using the CLI826
    - Configuring the Ping Test826
    - Configuring the Tracert Test827
- Appendix: Default Parameters828
Configuring System Logs829
- Overview830
- System Logs Configurations831
  - Using the GUI832
  - Using the CLI835
    - Configuring the Local Logs835
    - Configuring the Remote Logs836
- Configuration Example838
- Appendix: Default Parameters840

TP-Link T1500 Series - Page 736

Table of Contents

Related product manuals