February 2013
6-297
ColorQube® 9303 Family
dC972, dC976
General Procedures/Information
• 91-719-00 IOD head 4 Y: not converging.
• 91-720-00 IOD head 4 Y: position limit.
• 91-721-00 IOD calibration.
• 91-722-00 IOD calibration 2D.
• 91-725-00 IOD target.
• 91-726-00 IOD target: missing.
• 91-727-00 IOD target: corrupted.
• 91-728-00 IOD target: missing or corrupted.
• 91-729-00 IOD target: Y position out of range.
• 91-730-00 IOD target: Y position out of far range.
• 91-732-00 The IOD detects printhead 3 Y axis is at the limit of travel.
• 91-735-00 IOD non-static scanbar artifact.
• 91-736-00 IOD static scanbar artifact.
• 91-807-00 Attempt to read or write printhead 1 NVM HAY or HAU sections failed.
• 91-808-00 Attempt to read or write printhead 2 NVM HAY or HAU sections failed.
• 91-809-00 Attempt to read or write printhead 3 NVM HAY or HAU sections failed.
• 91-810-00 Attempt to read or write printhead 4 NVM HAY or HAU sections failed.
• 91-811-00 Machine has timed out waiting for the adjustment load task to complete read-
ing printhead NVM.
• 91-812-00 The required voltage adjustment exceeds the maximum on printhead 1.
• 91-813-00 The required voltage adjustment exceeds the maximum on printhead 2.
• 91-814-00 The required voltage adjustment exceeds the maximum on printhead 3.
• 91-815-00 The required voltage adjustment exceeds the maximum on printhead 4.
• 91-816-00 Voltage adjustment can not bring printhead 1 into tolerance.
• 91-817-00 Voltage adjustment can not bring printhead 2 into tolerance.
• 91-818-00 Voltage adjustment can not bring printhead 3 into tolerance.
• 91-819-00 Voltage adjustment can not bring printhead 4 into tolerance.
• 91-824-00 MARKDWR-PQM insufficient ink.
• 91-825-00 MARKDWR-PQM insufficient paper.
• 91-826-00 MARKDWR-PQM insufficient jets.
• 91-827-00 MARKDWR-PQM align needed.
• 91-828-00 MARKDWR-PQM Y dot position needed.
• 91-829-00 MARKDWR-PQM drum runout needed.
• 91-830-00 MARKDWR-PQM uniformity needed.
• 91-831-00 MARKDWR-PQM uniformity reset needed.
• 91-832-00 MARKDWR-PQM empty waste tray.
• 91-833-00 MARKDWR-PQM cleaning pages needed.
• 91-834-00 MARKDWR-PQM tool not usable.
• 91-835-00 MARKDWR-PQM tool manually disabled.
• 91-836-00 MARKDWR-PQM: system busy.
• 92-803-00 DSP2 overlay setup time-out.
• 92-804-00 DSP2 overlay cleanup time-out.
• 92-807-00 In dC972 automatic TRC generation is not implemented.
dC976 Ink Delivery Fault Recovery
Purpose
To prime the umbilical assembly and check valve unit after replacement of the umbilical
assembly, check valve unit (CVU), attached to and included with the umbilical assembly.
Failure to prime the CVU and umbilical assembly may result in:
• Purge air pressure leaking backwards through the assembly.
• Ink bubbling up from the reservoir into the ink reservoir air manifold.
• Reservoir assembly replacement.
• Umbilical replacement, if ink enters the purge line.
After umbilical or ink melt reservoir replacement, purge line connections to the reservoir must
be physically verified. The correct orientation of the connections is shown in REP 91.20.
Procedure
1. Enter service mode, GP 1.
2. Select the Maintenance tab.
3. Select dC976 Ink Delivery Fault Recovery.
4. Select the component that has been replaced:
• Lower Umbilical
• Upper Umbilical
• Ink Reservoir (This option has no benefit, use the other two options).
5. Select the start button to begin the procedure.
6. On completion of the procedure a message will be displayed of the success or failure.
NOTE: If a new umbilical has been installed then run the routine a second time. A single
priming routine may not be sufficient in all cases.
7. Select Close to return to the Maintenance routine window.
8. Select Call Closeout to exit service mode.