February 2013
2-38
ColorQube® 9303 Family
01L
Status Indicator RAPs
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new tray 5 control PWB PL 75.68 Item 8, or associated components.
3 Tray Module PWB
•Refer to WD 7.3, WD 7.4 and WD 7.5
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new 3 tray module PWB, PL 73.16 Item 4, or associated compo-
nents
Media Path Driver PWB
•Refer to WD 8.1, WD 8.2, WD 8.3, WD 8.4 and WD 8.5.
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new media path driver PWB, PL 1.15 Item 5 or associated compo-
nents.
Drum Driver PWB
•Refer to WD 9.1, WD 9.2, WD 9.3 and WD 9.4.
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new drum driver PWB, PL 1.15 Item 4, or associated components
IME Controller PWB
•Refer to WD 1.1, WD 9.5, WD 9.6 and WD 9.7
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new IME controller PWB, PL 92.10 Item 1, or associated compo-
nents.
Marking Unit Heater PWB
•Refer to WD 9.8
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new marking unit heater PWB, PL 92.10 Item 5, or associated com-
ponents.
Marking Unit Driver PWB
•Refer to WD 9.9, WD 9.10, WD 9.11 and WD 9.12
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new marking unit driver PWB, PL 92.10 Item 4, or associated com-
ponents.
Quad Wave Amp PWB
•Refer to WD 9.13
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new quad wave amp PWB, PL 92.10 Item 3, or associated compo-
nents.
Solenoid Patch PWB
•Refer to WD 9.14, WD 9.15 and WD 9.16
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new reservoir, PL 93.10 Item 10, or associated components.
Ink Load Entry PWB
•Refer to WD 9.17 and WD 9.18
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new ink load entry PWB, PL 93.10 Item 8, or associated compo-
nents.
Cleaning Unit PWB
•Refer to WD 9.19
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new cleaning unit PWB, PL 94.10 Item 21, or associated compo-
nents.
Printheads 1, 2, 3 and 4 PWB’s
•Refer to WD 9.20 and WD 9.21
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new printhead 1, 2, 3 or 4 PWB, PL 91.20 Item 3 and PL 91.25 Item
3.
IOD Pre-amplifier PWB
•Refer to WD 9.22
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new IOD assembly, PL 94.15 Item 1, or associated components.
LCSS PWB
• The LCSS low voltage power comes from its own power supply module as shown in WD
12.1. Refer to WD 12.1, WD 12.2, WD 12.3, WD 12.4 and WD 12.5
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new LCSS power supply module, PL 12.75 Item 2, LCSS PWB, PL
12.75 Item 1, or associated components.
HVF Control PWB
• The HVF low voltage power comes from its own power supply module as shown in WD
12.6. Refer to WD 12.6, WD 12.7, WD 12.8, WD 12.9, WD 12.10, WD 12.11, WD 12.12,
WD 12.13, WD 12.14 and WD 12.15
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new HVF PWB, PL 12.140 Item 2, or associated components.
BM PWB (Booklet maker)
• The BM low voltage power comes from the HVF power supply module as shown in WD
12.6. Refer to WD 12.6, WD 12.16, WD 12.17, WD 12.18 and WD 12.19.
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new BM PWB, PL 12.175 Item 10, or associated components.
Tri-folder PWB
• The tri-folder low voltage power comes from the HVF power supply module as shown in
WD 12.6. Refer to WD 12.6 and WD 12.20
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new tri-folder PWB, PL 12.205 Item 16, or associated components.
Inserter PWB
• The inserter low voltage power comes from the HVF power supply module as shown in
WD 12.14. Refer to WD 12.14, WD 12.21 and WD 12.22
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new inserter PWB, PL 12.310 Item 9, or associated components.
OCT PWB
• The OCT low voltage power comes from the media path driver PWB, as shown in WD 8.5.
Refer to WD 8.5 and WD 12.23.
• Repair the wiring as necessary, REP 1.1.
• If necessary, install a new OCT, PL 12.00 Item 1, or media path driver PWB, PL 1.15 Item
5.
To Next Page
Loading...
