Xerox ColorQube 9303 Series - Page 93

February 2013
2-69
ColorQube® 9303 Family
10-110-00 to 10-113-00, 10-125-00 to 10-128-00, 10-
Status Indicator RAPs
10-110-00 to 10-113-00, 10-125-00 to 10-128-00, 10-147-00,
10-148-00 Post Transfix Jam RAP
10-110-00 Timing sensor 11 detects that the sheet is too long.
10-111-00 Timing sensor 11 detects that the sheet is too short.
10-112-00 The lead edge is late to timing sensor 11.
10-113-00 The trail edge is late from timing sensor 11.
10-125-00 Timing sensor 12 detects that the sheet is too long.
10-126-00 Timing sensor 12 detects that the sheet is too short.
10-127-00 The lead edge was late to timing sensor 12.
10-128-00 The trail edge was late from timing sensor 12.
10-147-00 The lead edge is early to timing sensor 11.
10-148-00 The lead edge is early to timing sensor 12.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
WARNING
Do not clean the stripper blade. The stripper blade is very sharp and can cause injury. If
the stripper blade is dirty a new blade must be installed.
WARNING
Take care during this procedure. Sharp edges may be present that can cause injury.
• Check that the media loaded into the trays matches the UI display.
• Check for obstructions in the paper path.
• Check the jam clearance guide 3b is latched correctly, PL 10.12 Item 1.
• Ensure that the springs for both the front and rear latch forks, PL 10.10 Item 14, are not
broken or fallen off.
• Ensure that the springs are orientated the correct way. The longer end hook of the spring
should be hooked from under the stripper cam, PL 10.10 Item 18.
• If the displayed fault code is 10-112-00, check the transfix stripper blade, PL 10.20 Item
14 for damage. Refer to REP 10.6 Transfix Blade. Install new components as required.
•Go to dC135 CRU/HFSI Status. Check the count of the transfix stripper. If the count is
near end of life, install a new transfix stripper blade, PL 10.20 Item 14.
• If the displayed fault code is 10-112-00, check the drum stripper blade assembly, PL
10.12 Item 3 for damage or contamination. Refer to REP 10.21 Stripper Blade, Gate and
Baffle. Install new components as required.
• Check for multifeeds. If there are multifeeds, refer to the OF 8 Multifeed RAP.
• If glossy media is used, instruct the customer to feed the media from the bypass tray and
select glossy for the media type.
Procedure
Refer to Figure 1. Lower the drum stripper gate and baffle assembly, GP 31. Check that the
stripper blade shaft is installed correctly. Slide the shaft forwards and backwards and feel for
the shaft to engage on the detent. Raise the stripper blade into the operating position. Check
that the stripper blade shaft lock is engaging correctly at the front and rear.
The stripper
blade latch mechanism is good.
YN
Install new stripper components as necessary, PL 10.10, PL 10.12.
Check the drum stripper blade timing. Print three copies of TP 14 Drum Stripper Blade Test
Page.
Stripper blade timing is good.
YN
Check the stripper solenoid SOL10-021 PL 10.10 Item 3. Refer to 10-570-00 Stripper
Solenoid Over Current RAP.
Cheat the front door interlock. Enter dC330 code 10-018 to run the post transfix motor (M4), PL
10.10 Item 5.
The motor runs.
YN
Refer to WD 8.2. Check the post transfix motor (M4). Refer to:
• GP 10 How to Check a Motor.
• PJ303, Media path driver PWB.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Post transfix motor (M4), PL 10.10 Item 5.
• Media path driver PWB, PL 1.15 Item 5.
Observe roller drive J, PL 10.10 Item 1 and roller drive L, PL 10.10 Item 2. The rollers rotate.
YN
Check the gear drive, drive gears and roller drives, PL 10.10.
If necessary, install new components:
• Drive gears, PL 10.10 Item 13.
• Gear drive, PL 10.10 Item 4.
• Roller drive J, PL 10.10 Item 1.
• Roller drive L, PL 10.10 Item 2.
Unlatch the stripper gate, GP 31. Enter dC330 code 10-015, post transfix sensor (11), Q10-
015, PL 10.10 Item 6. Manually actuate Q10-015.
The display changes.
YN
Refer to WD 9.3. Check the post transfix sensor (11), Q10-015. Refer to:
• GP 11 How to Check a Sensor.
• PJ802, Drum driver PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
A