8.3 Alarm Message List
8-38
4036 MEMORY
ERROR
(WEARING FILE)
--- An error was detected at memory
check.
• The memory for the wear amount
file is damaged.
Initialize the wear amount file in the mainte-
nance mode, and then load the wear amount
file saved in the external memory device.
4037 MEMORY
ERROR
(STROKE
POSITION)
--- An error was detected at memory
check.
• The memory for the FULL/SHORT
OPEN position setting file is dam-
aged.
Initialize the FULL/SHORT OPEN position
setting file in the maintenance mode, and
then load the FULL/SHORT OPEN position
setting file saved in the external memory
device.
4038 MEMORY
ERROR
(PRESSURE
FILE)
--- An error was detected at memory
check.
• The memory for the dry-spotting
pressure file is damaged.
Initialize the dry-spotting pressure file in the
maintenance mode, and then load the dry-
spotting pressure file saved in the external
memory device.
4039 MEMORY
ERROR
(FORM CUT
FILE)
--- An error was detected at memory
check.
• The memory for the form cut file is
damaged.
Initialize the form cut file in the maintenance
mode, and then load the form cut file saved in
the external memory device.
4040 MEMORY
ERROR (SHOCK
LEVEL FILE)
--- An error was detected at memory
check.
• The memory for the shock level
file is damaged.
Initialize the shock level file in the mainte-
nance mode, and then load the shock level
file saved in the external memory device.
4041 MEMORY
ERROR
(SPOT IO
ALLOCATE FL)
--- An error was detected at memory
check.
• The memory for the spot I/O allo-
cation file is damaged.
Initialize the spot I/O allocation file in the
maintenance mode, and then load the spot
I/O allocation file saved in the external mem-
ory device.
4042 MEMORY
ERROR
(VISION FILE)
--- An error was detected at memory
check.
• The memory for the vision condi-
tion file is damaged.
Initialize the vision condition file in the main-
tenance mode, and then load the vision con-
dition file saved in the external memory
device.
4043 MEMORY
ERROR
(VISION
CALIBRATION)
--- An error was detected at memory
check.
• The memory for the vision calibra-
tion file is damaged.
Initialize the vision calibration file in the main-
tenance mode, and then load the vision cali-
bration file saved in the external memory
device.
4044 MEMORY
ERROR
(WELDING
PULSE COND
FILE)
--- An error was detected at memory
check.
• The memory for the welding pulse
condition file is damaged.
Initialize the welding pulse condition file in the
maintenance mode, and then load the weld-
ing pulse condition file saved in the external
memory device.
4045 MEMORY
ERROR
(WELDING
PULSE
SELECTION
FILE)
--- An error was detected at memory
check.
• The memory for the welding pulse
selection file is damaged.
Initialize the welding pulse s
election file in the
maintenance mode, and then load the weld-
ing pulse selection file saved in the external
memory device.
4046 MEMORY
ERROR
(CONVEYOR
CALIBRATION)
--- An error was detected at memory
check.
• The memory for the conveyor cali-
bration file is damaged.
Initialize the conveyor calibration file in the
maintenance mode, and then load the con-
veyor calibration file saved in the external
memory device.
4047 MEMORY
ERROR (MACRO
DEFINITION
FILE)
--- An error was detected at memory
check.
• The memory for the macro defini-
tion file is damaged.
Initialize the macro definition file in the main-
tenance mode, and then load the macro defi-
nition file saved in the external memory
device.
4048 MEMORY
ERROR
(SERVO S-GUN
FILE)
--- An error was detected at memory
check.
• The memory for the sealer gun
characteristics file is damaged.
Initialize the sealer gun characteristics file in
the maintenance mode, and then load the
sealer gun characteristics file saved in the
external memory device.
Alarm Message List
Alarm
Number
Message
Sub
Code
Cause Remedy
To Next Page
Loading...
