9
Figure 1: Front Panels of the AT-x930-28GTX and AT-x930-28GPX Switches ...................................................................19
Figure 2: Front Panels of the AT-x930-28GSTX, AT-x930-52GTX, and AT-x930-52GPX Switches....................................20
Figure 3: Back Panel of the AT-x930-28GTX, AT-x930-28GSTX, and AT-x930-52GTX Switches ......................................21
Figure 4: Back Panel of the AT-x930-28GPX and AT-x930-52GPX Switches .....................................................................21
Figure 5: Management Panel ...............................................................................................................................................26
Figure 6: AT-PWR150, AT-PWR250, and AT-PWR250-80 Power Supplies........................................................................27
Figure 7: AT-PWR800 and AT-PWR1200 Power Supplies ..................................................................................................28
Figure 8: LEDs for the 10/100/1000Base-T Ports on the AT-x930-28GTX, AT-x930-28GSTX, and AT-x930-52GTX
Switches ...............................................................................................................................................................................43
Figure 9: LEDs for the 10/100/1000Base-T Ports on the AT-x930-28GPX and AT-x930-52GPX Switches ........................45
Figure 10: SFP Port LEDs ....................................................................................................................................................46
Figure 11: SFP+ Port LEDs ..................................................................................................................................................47
Figure 12: Switch ID LED .....................................................................................................................................................49
Figure 13: Switch ID LED .....................................................................................................................................................50
Figure 14: Switch ID LEDs in the Low Power Mode.............................................................................................................50
Figure 15: AT-StackQS Card................................................................................................................................................53
Figure 16: Copper Breakout Cable.......................................................................................................................................53
Figure 17: AT-x9EM/XT4 Card .............................................................................................................................................55
Figure 18: Trunk of Ports S1 and S2 for a Stack of Two Switches.......................................................................................61
Figure 19: Trunk of Ports S1 and S2 for a Stack of Four Switches ......................................................................................62
Figure 20: Trunk of Ports S1 and S2 for a Stack of Eight Switches .....................................................................................63
Figure 21: Trunk of AT-StackQS Cards for a Stack of Two Switches ..................................................................................65
Figure 22: Trunk of AT-StackQS Cards for a Stack of Four Switches..................................................................................65
Figure 23: Trunk of AT-StackQS Cards for a Stack of Eight Switches.................................................................................66
Figure 24: Trunk of Copper Gigabit Ports for a Stack of Two Switches ...............................................................................67
Figure 25: Trunk of Copper Gigabit Ports for a Stack of Three Switches.............................................................................68
Figure 26: Trunk of Copper Gigabit Ports for a Stack of Four Switches...............................................................................68
Figure 27: Trunk of SFP Gigabit Ports for a Stack of Two AT-x930-28GSTX Switches.......................................................70
Figure 28: Trunk of SFP Gigabit Ports for a Stack of Three AT-x930-28GSTX Switches....................................................70
Figure 29: Trunk of SFP and Copper Gigabit Ports for a Mixed Stack of Four Switches .....................................................71
Figure 30: PORT Parameter in the Command Line Interface...............................................................................................76
Figure 31: Accessory Kit.......................................................................................................................................................90
Figure 32: Pre-installed Items...............................................................................................................................................91
Figure 33: Removing the Blank Panel ..................................................................................................................................95
Figure 34: Power Supply Accessory Items...........................................................................................................................96
Figure 35: Installing a Power Supply ....................................................................................................................................97
Figure 36: Improper Installation of a Power Supply..............................................................................................................98
Figure 37: Tightening the Captive Screws on the Power Supply..........................................................................................98
Figure 38: Installing the Power Cord Retaining Clip.............................................................................................................99
Figure 39: Installing a Blank Panel on a Power Supply Slot...............................................................................................100
Figure 40: Tightening the Captive Screws on the Blank Panel for the Power Supply Slot .................................................101
Figure 41: Loosening the Two Captive Screws on the AT-FAN09 Module ........................................................................106
Figure 42: Removing the AT-FAN09 Module......................................................................................................................106
Figure 43: Loosening the Captive Screw on the AT-FAN09ADP Module...........................................................................107
Figure 44: Removing the AT-FAN09ADP Module ..............................................................................................................107
Figure 45: Removing the Card from the Anti-static Bag .....................................................................................................108
Figure 46: Aligning the Card in the Slot..............................................................................................................................109
Figure 47: Seating the Card in the Switch ..........................................................................................................................109
Figure 48: Tightening the Captive Screw on the Card........................................................................................................110
Figures
To Next Page
Loading...
Need help?
General
