To Next PageTo Next Page
Need help?Do you have a question about the Allied Telesis AlliedWare Plus GS980MX Series and is the answer not in the manual?
General| VLANs | 4094 |
|---|---|
| Model | GS980MX Series |
| Type | Managed |
| Switching Capacity | 176 Gbps |
| Forwarding Rate | 131 Mpps |
| Jumbo Frame Support | 9KB |
| Operating Temperature | 0°C to 50°C |
| Power Consumption | Varies by model |
Explains symbols, formatting, and warnings used in the document.
Provides contact information and resources for technical support and sales.
Details the physical layout and components of the switch's front and rear panels.
Lists and describes the main features and specifications of the GS980MX Series switches.
Explains the specifications, speed, duplex, and PoE capabilities of twisted pair ports.
Details the Power over Ethernet (PoE) standards, classes, and budget for the switches.
Describes the ports supporting SFP/SFP+ transceivers and their link/activity LEDs.
Explains the Virtual Chassis Stacking (VCStack) feature and its advantages for network management.
Details the function and display of the Switch ID LED for stack identification.
Lists general rules and requirements for building a VCStack of GS980MX Series switches.
Explains stack trunks, their default and optional ports, and cabling requirements.
Provides examples of incorrect stack trunk configurations and their issues.
Describes the roles and main functions of master and member switches in a stack.
Explains the necessity and assignment of unique ID numbers for switches within a stack.
Lists key factors to consider when planning the configuration and setup of a switch stack.
Outlines essential safety warnings, including laser and electrical hazards, before installation.
Provides requirements for selecting an appropriate installation location for the switch.
Details the contents of the shipping box and how to unpack the GS980MX/10HSm switch.
Details the contents of the shipping box and how to unpack the GS980MX/18HSm switch.
Details the contents of the shipping box for 24- and 48-port switches.
Provides instructions on how to attach the four reusable bumper feet to the switch base.
Introduces the two methods for rack-mounting the GS980MX/10HSm switch.
Provides step-by-step instructions for installing the switch using RKMT-J14 brackets.
Details rack-mounting procedures for other GS980MX models using supplied brackets.
Illustrates and describes acceptable switch orientations when mounting on a wall.
Provides guidelines for wall-mounting switches, including stud types and material requirements.
Details the process of attaching the switch to a pre-installed plywood base on the wall.
Provides instructions for directly mounting the switch onto a concrete wall.
Explains the process of building a stack using default 10Gbps stacking ports without specific configuration.
Guides on powering switches one by one to control stack ID assignment and master selection.
Guides on powering all switches simultaneously for automatic ID assignment based on MAC addresses.
Explains how to establish a local management session using a console cable and terminal emulator.
Details how to use the SHOW STACK command to verify the operational status and configuration of the stack.
Introduces procedures for configuring member switches to use 5Gbps ports for stack trunks.
Briefly describes commands for configuring master and member switches for 5Gbps stacking.
Outlines the procedures for configuring the master switch for 5Gbps stacking ports.
Introduces procedures for configuring member switches to use 5Gbps ports for stack trunks.
Provides general steps for configuring member switches for stacking, including ID and priority settings.
Details the steps for configuring GS980MX/10HSm member switches for 5Gbps stacking.
Details the steps for configuring GS980MX/18HSm member switches for 5Gbps stacking.
Details the steps for configuring GS980MX/28PSm member switches for 5Gbps stacking.
Details the steps for configuring GS980MX/52PSm member switches for 5Gbps stacking.
Provides guidelines for connecting twisted pair cables to switch ports, including cable requirements.
Offers essential guidelines for handling SFP and SFP+ transceivers, including ESD precautions.
Provides step-by-step instructions for installing SFP or SFP+ transceivers into switch ports.
Details the installation procedure for SP10TW direct connect twinax cables.
Addresses issues related to no power and fan operation, suggesting checks for power connectivity.
Helps diagnose and resolve issues where a twisted pair port's LINK/ACT LED is off.
Guides on troubleshooting when the SFP/SFP+ transceiver LINK/ACT LED is off.
Provides solutions for troubleshooting when the SHOW STACK command output is incomplete.
Addresses problems where the switch fails to provide power to connected PoE devices.
Lists the physical dimensions and weights of the different GS980MX Series switch models.
Details the operating and storage temperature, humidity, and altitude specifications for the switches.
Provides maximum power consumption values and input voltages for all GS980MX Series switches.
Lists product certifications for EMI, EMC, Electrical Safety, and compliance marks.
Illustrates the pin layout for RJ-45 connectors on the switch's front panel.
