EasyManuals Logo

Cisco Catalyst 3750 Software Configuration Guide

Cisco Catalyst 3750
926 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #544 background imageLoading...
Page #544 background image
26-64
Catalyst 3750 Metro Switch Software Configuration Guide
78-15870-01
Chapter 26 Configuring QoS
Configuring Standard QoS
Switch(config-if)# mls qos dscp-mutation mutation1
Switch(config-if)# end
Switch# show mls qos maps dscp-mutation mutation1
Dscp-dscp mutation map:
mutation1:
d1 : d2 0 1 2 3 4 5 6 7 8 9
---------------------------------------
0 : 00 00 00 00 00 00 00 00 10 10
1 : 10 10 10 10 14 15 16 17 18 19
2 : 20 20 20 23 24 25 26 27 28 29
3 : 30 30 30 30 30 35 36 37 38 39
4 : 40 41 42 43 44 45 46 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Note In the above DSCP-to-DSCP-mutation map, the mutated values are shown in the body of the matrix. The
d1 column specifies the most-significant digit of the original DSCP; the d2 row specifies the
least-significant digit of the original DSCP. The intersection of the d1 and d2 values provides the mutated
value. For example, a DSCP value of 12 corresponds to a mutated value of 10.
Configuring Ingress Queue Characteristics
Depending on the complexity of your network and your QoS solution, you might need to perform all of
the tasks in the next sections. You will need to make decisions about these characteristics:
Which packets are assigned (by DSCP or CoS value) to each queue?
What drop percentage thresholds apply to each queue, and which CoS or DSCP values map to each
threshold?
How much of the available buffer space is allocated between the queues?
How much of the available bandwidth is allocated between the queues?
Is there traffic (such as voice) that should be given high priority?
These sections describe how to configure ingress queue characteristics:
Mapping DSCP or CoS Values to an Ingress Queue and Setting WTD Thresholds, page 26-65
(optional)
Allocating Buffer Space Between the Ingress Queues, page 26-66 (optional)
Allocating Bandwidth Between the Ingress Queues, page 26-67 (optional)
Configuring the Ingress Priority Queue, page 26-68 (optional)

Table of Contents

Other manuals for Cisco Catalyst 3750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750 and is the answer not in the manual?

Cisco Catalyst 3750 Specifications

General IconGeneral
Device TypeSwitch
Switching Capacity32 Gbps
Forwarding Rate38.7 Mpps
Stacking Bandwidth32 Gbps
RAM128 MB
Jumbo Frame SupportYes
Switch TypeManaged
ModelCatalyst 3750 Series
Uplink InterfacesSFP
Form FactorRack-mountable
MAC Address Table Size12, 000 entries
Routing ProtocolRIP, OSPF, EIGRP
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesLayer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)PoE
Operating Temperature-5 - 45 °C
Operating Humidity10% to 85% non-condensing

Related product manuals