Cisco RV110W Administration Guide

Configuring VPN
Configuring Basic VPN Settings (Site-to-Site VPN)
Cisco RV110W Administration Guide 100
5
Configuring Basic VPN Settings (Site-to-Site VPN)
The Cisco RV110W supports Site-to-Site VPN for a single gateway-to-gateway
VPN tunnel. In this configuration, the Cisco RV110W creates a secure connection
to another VPN-enabled router. For example, you can configure the Cisco RV110W
at a branch site to connect to the router at the corporate site, so that the branch
site can securely access the corporate network. You could have a router like the
Cisco RV220W that supports ten site-to-site VPN tunnels and have an
Cisco RV110W at each remote site to provide secure connectivity.
To configure basic VPN settings for a site-to-site connection:
STEP 1 Choose VPN > Basic VPN Setup.
STEP 2 In the Connection Name field, enter a name for the VPN tunnel.
STEP 3 In the Pre-Shared Key field, enter the pre-shared key, or password, that will be
exchanged between the two routers. It must be between 8 and 49 characters.
STEP 4 In the Endpoint Information fields, enter the following information:
• Remote Endpoint—Choose the way the remote endpoint, or the router to
which the Cisco RV110W will connect, is identified (by IP address - for
example,
192.168.1.1 - or fully-qualified domain name - for example,
cisco.com ).
• Remote WAN (Internet) IP Address—Enter the public IP address or domain
name of the remote endpoint.
• Local WAN (Internet) IP Address—Enter the public IP address or domain
name of the local endpoint (Cisco RV110W).
STEP 5 In the Secure Connection Remote Accessibility fields, enter the following
information:
• Remote LAN (Local Network) IP Address—Enter the private network (LAN)
address of the remote endpoint. This is the IP address of the internal network
at the remote site.
• Remote LAN Subnet Mask—Enter the private network (LAN) subnet mask
of the remote endpoint.
• Local LAN (Local Network) IP Address—Enter the private network (LAN)
address of the local network. This is the IP address of the internal network
on the Cisco RV110W.

Cisco RV110W Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100Base-T(X)
Networking standards	IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.3, IEEE 802.3u
VPN tunnels quantity	10
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Channels quantity	13 channels
Top Wi-Fi standard	Wi-Fi 4 (802.11n)
Ethernet LAN (RJ-45) ports	4
Input voltage	12 V
Rack mounting	No
Number of users	32 user(s)
Weight (imperial)	0.61 lbs
Dimensions (WxDxH)	150 x 150 x 30 mm
Operating temperature (T-T)	32 - 104 °F
Compliance industry standards	IEEE 802.3, IEEE 802.3u
Supported data transfer rates	10/100Mbps
Dimensions (W x D x H) (imperial)	5.91 x 5.91 x 1.18 \
WLAN data transfer rates supported	11, 54 Mbit/s
Supported network protocols	PPPoE, DHCP, PPTP, L2TP, IGMP, RSTP
Antennas quantity	2
Antenna gain level (max)	1.8 dBi
Firewall security	VPN
Security algorithms	WEP, WPA, WPA2, WPS
MAC address filtering	-
Product color	Black
Certification	FCC, CE, IC, cUL, Wi-Fi
Storage temperature (T-T)	-20 - 70 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Width	150 mm
Height	30 mm
Weight	300 g