Cisco RV110W Administration Guide

Configuring the Wireless Network
Configuring Basic Wireless Settings
Cisco RV110W Administration Guide 67
3
STEP 7 (Optional) In the Passphrase field, enter an alphanumeric phrase (longer than eight
characters for optimal security) and click Generate Key to generate four unique
WEP keys in the WEP Key fields below.
If you want to provide your own key, enter it directly in the Key 1 field
(recommended). The length of the key should be 5 ASCII characters (or 10
hexadecimal characters) for 64-bit WEP and 13 ASCII characters (or 26
hexadecimal characters) for 128-bit WEP. Valid hexadecimal characters are 0 to 9
and A to F.
STEP 8 In the TX Key field, choose which key to use as the shared key that devices must
use to access the wireless network.
STEP 9 Click Save to save your settings.
STEP 10 Click Back to go back to the Basic Settings page.
Configuring WPA-Personal, WPA2-Personal, and WPA2-Personal Mixed
The WPA Personal, WPA2 Personal, and the WPA2 Personal Mixed security
modes offer strong security to replace WEP.
• WPA-Personal—WPA is part of the wireless security standard (802.11i)
standardized by the Wi-Fi Alliance and was intended as an intermediate
measure to take the place of WEP while the 802.11i standard was being
prepared. WPA-Personal supports Temporal Key Integrity Protocol (TKIP)
and Advanced Encryption Standard (AES) encryption.
• WPA2-Personal—(Recommended) WPA2 is the implementation of the
security standard specified in the final 802.11i standard. WPA2 supports
AES encryption and this option uses Preshared Key (PSK) for authentication.
• WPA2-Personal Mixed—Allows both WPA and WPA2 clients to connect
simultaneously using PSK authentication.
The personal authentication is the PSK that is an alphanumeric passphrase shared
with the wireless peer.
To configure the WPA Personal security mode:
STEP 1 In the Wireless Table (Wireless > Basic Settings), check the box for the network
you want to configure.
STEP 2 Click Edit Security Mode. The Security Settings page appears.

Cisco RV110W Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100Base-T(X)
Networking standards	IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.3, IEEE 802.3u
VPN tunnels quantity	10
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Channels quantity	13 channels
Top Wi-Fi standard	Wi-Fi 4 (802.11n)
Ethernet LAN (RJ-45) ports	4
Input voltage	12 V
Rack mounting	No
Number of users	32 user(s)
Weight (imperial)	0.61 lbs
Dimensions (WxDxH)	150 x 150 x 30 mm
Operating temperature (T-T)	32 - 104 °F
Compliance industry standards	IEEE 802.3, IEEE 802.3u
Supported data transfer rates	10/100Mbps
Dimensions (W x D x H) (imperial)	5.91 x 5.91 x 1.18 \
WLAN data transfer rates supported	11, 54 Mbit/s
Supported network protocols	PPPoE, DHCP, PPTP, L2TP, IGMP, RSTP
Antennas quantity	2
Antenna gain level (max)	1.8 dBi
Firewall security	VPN
Security algorithms	WEP, WPA, WPA2, WPS
MAC address filtering	-
Product color	Black
Certification	FCC, CE, IC, cUL, Wi-Fi
Storage temperature (T-T)	-20 - 70 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Width	150 mm
Height	30 mm
Weight	300 g