Danfoss VLT Programming Guide

0-37 Display Text 1
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If to be displayed permanently select Display Text 1 in par. 0-20
Display
Line 1.1 Small
, par. 0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small , par. 0-23 Display
Line 2 Large
or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the LCP to change a
character. Use the
◀
and
▶
buttons to move the cursor. When a character is highlighted by the
cursor, it can be changed. Use the
▲
or
▼
buttons on the LCP to change a character. A character
can be inserted by placing the cursor between two characters and pressing
▲
or
▼
.
0-38 Display Text 2
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If to be displayed permanently select Display Text 2 in par. 0-20
Display
Line 1.1 Small
, par. 0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small , par. 0-23 Display
Line 2 Large
or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the LCP to change a
character. Use the
◀
and
▶
buttons to move the cursor. When a character is highlighted by the
cursor, this character can be changed. A character can be inserted by placing the cursor between
two characters and pressing
▲
or
▼
.
0-39 Display Text 3
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If to be displayed permanently select Display Text 3 in par. 0-20
Display
Line 1.1 Small
,par. 0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small , par. 0-23 Display
Line 2 Large
or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the LCP to change a
character. Use the
◀
and
▶
buttons to move the cursor. When a character is highlighted by the
cursor, this character can be changed. A character can be inserted by placing the cursor between
two characters and pressing
▲
or
▼
.
3.2.6 LCP Keypad, 0-4*
Enable, disable and password protect individual keys on the LCP.
0-40 [Hand on] Key on LCP
Option: Function:
[0] Disabled No function
[1] * Enabled [Hand on] Key enabled
[2] Password Avoid unauthorized start in Hand mode. If par. 0-40
[Hand on] Key on LCP is included in the My
Personal Menu, then define the password in par. 0-65
Personal Menu Password . Otherwise define
the password in par. 0-60
Main Menu Password .
[3] Enabled without OFF
[4] Password without OFF
[5] Enabled with OFF
[6] Password with OFF
VLT
®
HVAC Drive Programming Guide 3 Parameter Description
MG.11.C9.02 - VLT
®
is a registered Danfoss trademark 43
3

Danfoss VLT Specifications

General

Frequency	50/60 Hz
Enclosure	IP20, IP21, IP55, IP66
Series	VLT
Control Technique	Flux Vector Control
Output Voltage	0-Vinput
Control Method	Fieldbus
Communication Interface	PROFIBUS, CANopen
Protection Features	Overload, Overvoltage, Undervoltage, Short Circuit, Ground Fault
Cooling Method	Liquid Cooled
Storage Temperature	-25°C to +70°C
Relative Humidity	5-95% non-condensing
Altitude	Up to 1000m (3280ft) without derating, up to 4000m (13120ft) with derating
Operating Temperature	-10°C to +50°C (14°F to 122°F)