Why is the trace faint or missing on my EDAN F9 Express?
If you're getting a faint trace or no trace at all on your EDAN Medical Equipment, make sure you're using the paper recommended by the manufacturer. Also, ensure that the paper drawer is locked by sliding it in until both latches are in position.
What to do if my EDAN F9 Express Medical Equipment has no display?
If your EDAN Medical Equipment shows no display, the issue might stem from a loose power cable. Ensure it's securely tightened. Alternatively, the fuse could be blown, requiring a replacement. Another possibility is that the battery is depleted; in this case, connect the equipment to an AC power supply.
Why is the trend a beeline on EDAN Medical Equipment?
If the trend on your EDAN Medical Equipment is a beeline, there may be a connector failure. Try moving or contacting the catheter. If the trend shows no fluctuation, change the intrauterine cable.
Why only IUP peak but no baseline on EDAN Medical Equipment?
If you're seeing only the IUP peak but no baseline on your EDAN Medical Equipment, the zero adjustment might be incorrect. Try zeroing the system.
How to fix a paper jam in EDAN F9 Express Medical Equipment?
If you're experiencing a paper jam with your EDAN Medical Equipment, it could be due to using the wrong type of paper or if the paper is dampened. Ensure you load the paper correctly and protect it from moisture.
What causes a doubtful FHR on EDAN F9 Express?
If you're getting a doubtful FHR reading on your EDAN Medical Equipment, it could be wrongly recording the maternal heart rate. Try changing the position of the ultrasound transducer. Another cause might be a poorly placed transducer recording mixed noise; adjust its position accordingly.
Why is there ECG signal interference on my EDAN F9 Express Medical Equipment?
If you observe big ECG signal interference or a thick baseline on your EDAN Medical Equipment, it might be due to abnormal electrode placement or invalid electrodes. Check the electrodes' placement and validity. Also, ensure the cable connector is securely connected. Lastly, verify that the power socket has a standard ground wire.
What to do if NIBP and SpO have no results on EDAN F9 Express?
If your EDAN Medical Equipment shows 'NIBP and SpO have no 2 results', check if the NIBP cuff is properly wrapped around the patient's arm. Extend the catheter and check its connection, if the NIBP cannot be inflated. Also, ensure the hose connector plug is securely connected to the NIBP socket and that the SpO transducer is well-connected to the SpO socket. If none of these resolve the issue, try shutting off the power and then switching it back on.
Why is the trace inconstant on my EDAN F9 Express?
If the EDAN Medical Equipment displays an inconstant trace or display, it could be due to several factors. If the patient is overweighted, monitor FHR with DECG. Ensure the ultrasound transducer is properly positioned for a better signal. Check for a loose belt and tighten it. Wipe off any superfluous aquasonic coupling gel, or use the recommended quantity if there is inadequate gel. Frequent fetal or maternal movements can also interfere; in these cases, delay monitoring or ask the patient to stay still.
Why is the trace quality bad on my EDAN F9 Express?
If you're getting a bad trace quality or fluctuant TOCO baseline on your EDAN Medical Equipment, the belt might be too tight or too loose; try adjusting it. Also, if the belt has no elasticity, renew it. Maternal or frequent fetal movements can also cause this issue, so request the patient to calm down and stay still or delay the monitoring.
Outlines critical safety instructions and guidelines for proper and safe use of the device.
Lists critical warnings and precautions to prevent injury or damage during instrument operation.
Provides step-by-step instructions for setting up and installing the monitor.
Provides step-by-step instructions for loading the thermal printer paper correctly.
Details the procedure for powering on the monitor and checking its initial state.
Provides instructions on how to properly connect various transducers to the monitor.
Explains how to perform non-invasive blood pressure (NIBP) monitoring.
Troubleshooting steps when NIBP or SpO2 measurements yield no results.
General| Waterproof Rating | IPX1 |
|---|---|
| Battery | Rechargeable lithium-ion battery |
| Category | Fetal and Maternal Monitor |
| FHR Measurement Range | 50 to 240 bpm |
| FHR Accuracy | ±1 bpm |
| Ultrasound Frequency | 1 MHz |
| Battery Life | Approx. 4 hours |
| Printing | Thermal printer |
| Paper Speed | 1, 2, 3 cm/min |
| Interfaces | USB, RS-232 |
| Parameters | FHR, TOCO |
| Power Supply | 100-240 V~ 50/60 Hz |
| Weight | Approximately 3.5 kg |
| Printout | Real-time and recall printout |
| Display | 12.1-inch color TFT LCD screen, folding up to 90 degrees |
To Next Page
