3-7
Chap. 3 OPERATION USING THE KEYPAD
Basic key operation
This section gives a description of the basic key operation in "Quick Setup," following the example of the function code data
changing procedure shown in Figure 3.2.
This example shows you how to change function code F01 data (Frequency command source) from the factory default "
/
keys on keypad (F01 = 0)" to "Current input to terminal [C1] (C1 function) (4 to 20 mA DC) (F01 = 2)."
(1) Turn the inverter ON. It automatically enters Running mode. In that mode, press the
key to switch to Programming
mode. The function selection menu appears. (In this example,
*fn:
is displayed.)
(2) If anything other than
*fn:
is displayed, use the and keys to display
*fn:
.
(3) Press the
key to proceed to the list of function codes.
(4) Use the
and keys to display the desired function code (
f
01
in this example), then press the key.
The data of this function code appears. (In this example, data
0
of
f
01
appears.)
(5) Change the function code data using the
and keys. (In this example, press the key two times to change data
0
to
2
.)
(6) Press the
key to establish the function code data.
The
saue
appears and the data will be saved in the memory inside the inverter. The display will return to the function code
list, then move to the next function code. (In this example,
f
02
.)
Pressing the
key instead of the key cancels the change made to the data. The data reverts to the previous value, the
display returns to the function code list, and the original function code reappears.
(7) Press the
key to return to the menu from the function code list.
Cursor movement
You can move the cursor when changing function code data by holding down the
key for 1 second or longer in the
same way as with the frequency settings. This action is called "Cursor movement."
It is possible to change or add function code items subject to quick setup. For details, consult your Fuji Electric
representatives.
3.4.2 Setting up function codes -- Menu #1 "Data Setting" --
Menu #1 "Data Setting" (
!f__
through
!y__
) in Programming mode allows you to set up all function codes.
To set function codes in this menu, it is necessary to set function code E52 to "0" (Function code data editing mode) or "2"
(Full-menu mode).
The menu transition in Menu #1 "Data Setting" is just like that in Menu #0 "Quick Setup."
Basic key operation
The basic key operation in Menu #1 "Data Setting" is just like that in Menu #0 "Quick Setup."
(1) Turn the inverter ON. It automatically enters Running mode. In that mode, press the
key to switch to Programming
mode. The function selection menu appears.
(2) Use the
and keys to display the desired function code group from the choices
!f__
through
!y__
.
(3) Press the
key to proceed to the list of function codes for the selected function code group.
(4) Use the
and keys to display the desired function code, then press the key.
The data of this function code appears.
(5) Change the function code data using the
and keys.
(6) Press the
key to establish the function code data.
The
saue
appears and the data will be saved in the memory inside the inverter. The display will return to the function code
list, then move to the next function code.
Pressing the
key instead of the key cancels the change made to the data. The data reverts to the previous value, the
display returns to the function code list, and the original function code reappears.
(7) Press the
key to return to the menu from the function code list.
3.4.3 Checking changed function codes -- Menu #2 "Data Checking" --
Menu #2 "Data Checking" in Programming mode allows you to check function codes that have been changed. Only the
function codes whose data has been changed from the factory defaults are displayed on the LED monitor. You can refer to the
function code data and change it again if necessary. To check function codes in Menu #2 "Data Checking," it is necessary to set
function code E52 to "1" (Function code data check mode) or "2" (Full-menu mode).
The menu transition in Menu #2 "Data Checking" is just like that in Menu #0 "Quick Setup."
To Next Page
Loading...
