HP VSR1000 Configuration Guide

273
[SwitchB-Vlan-interface100] ripng 1 enable
[SwitchB-Vlan-interface100] quit
# Configure Switch C.
<SwitchC> system-view
[SwitchC] ripng 1
[SwitchC-ripng-1] quit
[SwitchC] interface vlan-interface 200
[SwitchC-Vlan-interface200] ripng 1 enable
[SwitchC-Vlan-interface200] quit
3. Configure RIPng IPsec policies:
# On Switch A, create an IPsec proposal named tran1, and set the encapsulation mode to
transport mode, the security protocol to ESP, the encryption algorithm to DES, and authentication
algorithm to SHA1; create an IPsec policy named policy001, specify the manual mode for it,
reference IPsec proposal tran1, set the SPIs of the inbound and outbound SAs to 12345, and the
keys for the inbound and outbound SAs using ESP to abcdefg.
[SwitchA] ipsec proposal tran1
[SwitchA-ipsec-proposal-tran1] encapsulation-mode transport
[SwitchA-ipsec-proposal-tran1] transform esp
[SwitchA-ipsec-proposal-tran1] esp encryption-algorithm des
[SwitchA-ipsec-proposal-tran1] esp authentication-algorithm sha1
[SwitchA-ipsec-proposal-tran1] quit
[SwitchA] ipsec policy policy001 10 manual
[SwitchA-ipsec-policy-manual-policy001-10] proposal tran1
[SwitchA-ipsec-policy-manual-policy001-10] sa spi outbound esp 12345
[SwitchA-ipsec-policy-manual-policy001-10] sa spi inbound esp 12345
[SwitchA-ipsec-policy-manual-policy001-10] sa string-key outbound esp abcdefg
[SwitchA-ipsec-policy-manual-policy001-10] sa string-key inbound esp abcdefg
[SwitchA-ipsec-policy-manual-policy001-10] quit
# On Switch B, create an IPsec proposal named tran1, and set the encapsulation mode to
transport mode, the security protocol to ESP, the encryption algorithm to DES, and authentication
algorithm to SHA1; create an IPsec policy named policy001, specify the manual mode for it,
reference IPsec proposal tran1, set the SPIs of the inbound and outbound SAs to 12345, and the
keys for the inbound and outbound SAs using ESP to abcdefg.
[SwitchB] ipsec proposal tran1
[SwitchB-ipsec-proposal-tran1] encapsulation-mode transport
[SwitchB-ipsec-proposal-tran1] transform esp
[SwitchB-ipsec-proposal-tran1] esp encryption-algorithm des
[SwitchB-ipsec-proposal-tran1] esp authentication-algorithm sha1
[SwitchB-ipsec-proposal-tran1] quit
[SwitchB] ipsec policy policy001 10 manual
[SwitchB-ipsec-policy-manual-policy001-10] proposal tran1
[SwitchB-ipsec-policy-manual-policy001-10] sa spi outbound esp 12345
[SwitchB-ipsec-policy-manual-policy001-10] sa spi inbound esp 12345
[SwitchB-ipsec-policy-manual-policy001-10] sa string-key outbound esp abcdefg
[SwitchB-ipsec-policy-manual-policy001-10] sa string-key inbound esp abcdefg
[SwitchB-ipsec-policy-manual-policy001-10] quit
# On Switch C, create an IPsec proposal named tran1, and set the encapsulation mode to
transport mode, the security protocol to ESP, the encryption algorithm to DES, and authentication

HP VSR1000 Specifications

General

Model	VSR1000
Category	Network Router
Product Type	Router
Manufacturer	HP
Series	VSR
Form Factor	Rack-mountable
IPSec VPN Throughput	200 Mbps
Virtualization Support	Yes
Maximum Throughput	1 Gbps
Routing Protocols	OSPF, BGP
Virtualization Platforms	VMware
Management	Web-based management, CLI
Remote Management Protocol	SNMP, SSH, Telnet
Encryption	AES, 3DES
VPN Support	IPSec
Firewall Protection	Stateful packet inspection