IDEC OpenNet series User Manual

INDEX
OpenNet Controller User’s Manual v
length code 24-6
line
connection 23-2
control signals RS232C 17-27
linear conversion 19-4
link
register bit designation 6-19
registers
for DeviceNet network communication 25-7
for LonWorks network communication 26-8
for remote I/O system 24-2
LJMP 18-1
LOD and LODN instructions 7-2
logical device
no. 24-6
number 24-4
LON 26-1
LonMaker 26-2, 26-12
LonTalk protocol 26-2
LonWorks 26-1
interface module 2-39
network system setup 26-3
LRET 18-3
M MAC ID 25-6
maintain outputs while CPU stopped M8011 6-9
maintaining catch input 5-8
maintenance mode 2-2, 17-2
manipulated variable 20-13
mapping 24-5
master
and slave station numbers 21-2
control instruction 7-25
MCS and MCR instructions 7-25
media access control identifier 25-6
memory
backup error run/stop selection 5-2
card 2-6, 5-19
connector 2-2
eject button 2-2
map 26-14
message service 26-13
modem
cable 1C 23-1
initialization string selection 23-3
mode 23-1
status 23-3
data register 23-8
modifying application program 26-13
module
ID selection 5-5
specifications 2-1
monitor operation 4-7
monitoring PLC status 22-2
mounting
direction 3-4
on DIN rail 3-3
MOV 9-1
move 9-1
move not 9-5
MOVN 9-5
MUL 11-1
multiple usage of MCS instructions 7-26
multiplication 11-1
N N data
repeat set 9-10
set 9-9
NEG 12-5
negate 12-5
network
configuration information 26-2
management 26-2, 26-12
variables 26-2, 26-9, 26-23
Neuron chip 26-2
I/O pins 26-13, 26-15
no operation 8-6
node
address 24-4, 25-6
information remote I/O 24-6
number 24-4
NOP 8-6
normal operating conditions 2-4
NRS 9-10
NSET 9-9
NV 26-2
O on-line mode protocol selection 23-3
opcode 8-3
open
bus tab 24-13
network communication system 1-3
system interconnection OSI 26-2
opennet interface module A-4
operand
allocation numbers 6-2
for data link master station 6-5
for data link slave station 6-5
for functional modules 6-4
for master module 6-4
areas discontinuity 8-5
operands
digital I/O module 6-18
functional module 6-18
operating
procedure 23-11
data link system 21-11
status during errors 27-4
operation
basics 4-1
register 7-7
operational state 23-2
OR and ORN instructions 7-4
OR LOD instruction 7-5
OR word 12-1
originate mode 23-2, 23-4
ORW 12-1
OSI 26-2
OUT and OUTN instructions 7-2
output
during errors 27-4
hold or load off 25-6
module 2-16
terminal arrangement 2-22
modules A-3
network variables 26-23
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

IDEC OpenNet series Specifications

General

Brand	IDEC
Model	OpenNet series
Category	Controller
Language	English