IDEC OpenNet series User Manual

INDEX
OpenNet Controller User’s Manual vii
calendar/clock
using a user program 15-7
using WindLDR 15-7
communication parameters 23-10
using WindLDR 17-3
SFR and SFRN instructions 7-20
SFR(N) shifting flag M8012 6-10
SFTL 13-1
SFTR 13-3
shift
left 13-1
register instructions 7-20
right 13-3
simple operation 4-4
simultaneous refresh mode 21-10
single output instruction 7-24
skip 17-18
slave
station
communication completion relay
M8140-M8176 21-6
M8177 21-6
numbers 21-2
software version 25-7, 26-17
SOTU and SOTD instructions 7-24
SOTU/SOTD instructions using with program
branching 18-2
source
and destination operands 8-3
operand 8-3
special data registers 6-12
for data link communication error 21-4
for data link master/slave stations 6-17
for error information 27-3
for high-speed counter 5-10, 6-13
for INTERBUS 6-13
for INTERBUS master information 24-10
for modem mode 6-16
for remote I/O node information 24-6
for RS232C line control signals 17-27
special functions 5-1
special internal relay allocation numbers 6-6
special internal relays
for data link communication 21-6
for high-speed counter 5-10
for INTERBUS master information 24-11
specifications
CPU module 2-5
data link 21-1
DeviceNet slave module 25-4
function 2-5
general 2-4
LonWorks interface module 26-5
remote I/O master module 2-37
remote I/O system 24-2
user communication mode 17-1
start
and result internal relays 23-2
control M8000 6-9
delimiter 17-16
start/stop
operation 4-2
remote I/O communication 24-12
schematic 4-2
using power supply 4-3
using WindLDR 4-2
starting operation 25-9, 26-12
station numbers 21-2
status
code
receive 17-21
transmit 17-9
data register modem mode 23-8
LED 2-2
transition number INTERBUS master 24-10
status LEDs 26-15
step response method 20-9
stop
input 4-3, 5-1
system status 2-6
STOP mode control signal statuses 17-28
structure 26-23
of an advanced instruction 8-3
SUB 11-1
subtraction 11-1
SUM 11-11
SX5 communication I/O terminals A-4
SX5D communication I/O terminals 25-2
SX5L communication I/O terminals 26-3
SX5S communication I/O terminals 24-3
system
error information INTERBUS master 24-10
setup 1-3
data link 21-2
DeviceNet network 25-2
LonWorks network 26-3
modem mode 23-1
remote I/O system 24-1
user communication 17-2
statuses 4-3
at stop, reset, and restart 2-6
T table
ASCII character code 17-26
display unit character codes 16-7
TC= and TC≥ instructions 7-16
telephone number 23-3, 23-5
terminal
block 2-3
connection 3-10
terminator 25-4, 26-7
timeout receive 17-17
timer
accuracy 7-9
comparison instructions 7-16
instruction using with program branching 18-2
or counter
as destination operand 8-3
as source operand 8-3
timer/counter preset value
changed M8124 6-11
sum check error 27-4
TML, TIM, TMH, and TMS instructions 7-8
transceiver 26-2
transmission
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

IDEC OpenNet series Specifications

General

Brand	IDEC
Model	OpenNet series
Category	Controller
Language	English