Keithley 2657A User Manual

Section 5: Introduction to TSP operation Model 2657A High Power System SourceMeter® Instrument Reference Manual
5-8 2657A-901-01 Rev. B/December 2012
LAN and LXI
The LAN commands have options that allow you to review and configure network settings.
The lan.config.* commands allow you to configure LAN settings over the remote interface. Note
that you must send lan.applysettings() for the configuration settings to take effect.
The lan.status.* commands help you determine the status of the LAN.
The lan.trigger[N].* commands allow you to set up and assert trigger events that are sent over
the LAN.
Other LAN commands allow you to reset the LAN, restore defaults, check LXI domain information,
and enable or disable the Nagle algorithm.
lan.applysettings() (on page 7-108)
lan.autoconnect
(on page 7-109)
lan.config.dns.address[N]
(on page 7-109)
lan.config.dns.domain
(on page 7-110)
lan.config.dns.dynamic
(on page 7-110)
lan.config.dns.hostname
(on page 7-111)
lan.config.dns.verify
(on page 7-112)
lan.config.duplex
(on page 7-112)
lan.config.gateway
(on page 7-113)
lan.config.ipaddress
(on page 7-113)
lan.config.method
(on page 7-114)
lan.config.speed
(on page 7-115)
lan.config.subnetmask
(on page 7-115)
lan.linktimeout
(on page 7-116)
lan.lxidomain
(on page 7-117)
lan.nagle
(on page 7-117)
lan.reset()
(on page 7-118)
lan.restoredefaults()
(on page 7-118)
lan.status.dns.address[N]
(on page 7-119)
lan.status.dns.name
(on page 7-119)
lan.status.duplex
(on page 7-120)
lan.status.gateway
(on page 7-120)
lan.status.ipaddress
(on page 7-121)
lan.status.macaddress
(on page 7-121)
lan.status.port.dst
(on page 7-122)
lan.status.port.rawsocket
(on page 7-122)
lan.status.port.telnet
(on page 7-123)
lan.status.port.vxi11
(on page 7-123)
lan.status.speed
(on page 7-124)
lan.status.subnetmask
(on page 7-124)
lan.timedwait
(on page 7-125)
lan.trigger[N].assert()
(on page 7-125)
lan.trigger[N].clear()
(on page 7-126)
lan.trigger[N].connect()
(on page 7-127)
lan.trigger[N].connected
(on page 7-127)
lan.trigger[N].disconnect()
(on page 7-128)
lan.trigger[N].EVENT_ID
(on page 7-128)
lan.trigger[N].ipaddress
(on page 7-129)
lan.trigger[N].mode
(on page 7-130)
lan.trigger[N].overrun
(on page 7-131)
lan.trigger[N].protocol
(on page 7-131)
lan.trigger[N].pseudostate
(on page 7-132)
lan.trigger[N].stimulus
(on page 7-132)
lan.trigger[N].wait()
(on page 7-134)
localnode.description
(on page 7-134)
localnode.password
(on page 7-136)

Keithley 2657A Specifications

General

Brand	Keithley
Model	2657A
Category	Measuring Instruments
Language	English