Mircom PRO-2000 Series - List of Figures

PRO-2000 Installation and Operation Manual
iii
List of Figures
Figure 1: LCD Display ................................................................................................................................... 2
Figure 2: X2, Synoptic sketch of the PRO-2000, X2 series........................................................................... 5
Figure 3: Lithium Battery Jumper .................................................................................................................. 6
Figure 4: X2S, Installation Layout.................................................................................................................. 8
Figure 5: X2E, Installation Layout.................................................................................................................. 9
Figure 6: X2M, Installation Layout................................................................................................................. 10
Figure 7: Terminal Connections .................................................................................................................... 12
Figure 8: Battery Hookup............................................................................................................................... 13
Figure 9: Synoptic Sketch of the PR0-2000, X6 Series................................................................................. 14
Figure 10: Micro-processor (MPU) ................................................................................................................ 15
Figure 11: X6S, Installation Layout................................................................................................................ 17
Figure 12: X6B, Installation Layout................................................................................................................ 18
Figure 13: X6E, Installation Layout................................................................................................................ 19
Figure 14: X6M, Installation Layout............................................................................................................... 20
Figure 15: Battery Hookup............................................................................................................................. 21
Figure 16: Synoptic Sketch of the PRO-2000, X0 Series.............................................................................. 23
Figure 17: X0S, Installation Layout................................................................................................................ 25
Figure 18: X0E, Installation layout................................................................................................................. 26
Figure 19: X0M, Installation Layout............................................................................................................... 27
Figure 20: X0S, Installation Layout with Power Supply and Batteries........................................................... 28
Figure 21: X0E, Installation Layout with Power Supply and Batteries........................................................... 29
Figure 22: X0M Installation Layout with Power Supply and Batteries ........................................................... 30
Figure 23: PRO-2000 Networked Panels ...................................................................................................... 31
Figure 24: X2 and X6 Network Wiring to a Repeater, X0.............................................................................. 32
Figure 25: Networking The X2 and X6 Using The Communication Card ...................................................... 33
Figure 26: MPU (Main Processing Unit) Card ............................................................................................... 34
Figure 27: MPU Backplane Connectors ........................................................................................................ 35
Figure 28: LCD Card ..................................................................................................................................... 38
Figure 29: LCD Backplane Connectors......................................................................................................... 38
Figure 30: Expansion Card and LCD Backplane........................................................................................... 40
Figure 31: Communication Card Connections............................................................................................... 44
Figure 32: Communication Card Wiring - Loop/Stub Mode........................................................................... 45
Figure 33: APS-14127-00 Auxiliary Power Supply........................................................................................ 46
Figure 34: APS-14127-00 Auxiliary Power Supply Connector ...................................................................... 47
Figure 35: APS-14127-00 Auxiliary Power Supply Typical Connection ........................................................ 47
Figure 36: APS-14127-00 Auxiliary Power Supply LED Indicators ............................................................... 48
Figure 37: 12 Zone Supervised Output Card................................................................................................. 49
Figure 38: Supervised Output Wiring ............................................................................................................ 51
Figure 39:
24/32 Zone Supervised Input Card.................................................................................... 52
Figure 40: Supervised Input Wiring ............................................................................................................... 54
Figure 41: ADI - Addressable Device Interface Card and Connections ........................................................ 55
Figure 42: ADI Driver Module........................................................................................................................ 55
Figure 43: ADI Card Wiring - Stub and Loop Mode....................................................................................... 57
Figure 44: ADI Card Wiring - Supervised Relay Outputs .............................................................................. 58
Figure 45: MIMIC Driver Module and Connections ....................................................................................... 59
Figure 46: LCD Expander Card and Connections......................................................................................... 60
Figure 47: 2 Wire Class B Initiating Circuit Configuration of Monitor Module................................................ 62
Figure 48: 2 Wire Style B Initiating Circuit Configuration of Monitor Module................................................. 63
Figure 49: Class B Indicating Circuit Wiring of Control Module..................................................................... 64
Figure 50: Typical Isolator Module Wiring - Using EOL Relay for Line Supervision...................................... 65
Figure 51: ADI CARD - Typical Wiring Diagram Number 1 for Control Module In Release Configuration.... 67
Figure 52: ADI CARD - Typical Wiring Diagram Number 2 for Control Module In Release Configuration.... 68
Figure 53: SI Card Typical Wiring Diagram for Releasing Circuit.................................................................. 69
Figure 54: SO Card Typical Wiring Diagram for Releasing Circuit................................................................ 70
Figure 55: LCD Panel.................................................................................................................................... 71