Reference Manual Rev 1.13
Page 4 004R-646-113
12.9.2. IDLE (Idle time) ........................................................................................... 80
12.9.3. MODE (Capture mode) ............................................................................... 80
12.10. AXLE (K422) ............................................................................................................... 81
12.10.1. MIN.WGT (Minimum weight) ....................................................................... 81
12.10.2. HYS (Hysteresis) ........................................................................................ 81
12.10.3. WINDOW (Window size) ............................................................................. 81
12.10.4. MIN.TIM (Minimum time) ............................................................................ 81
12.10.5. IDLE (Idle time) ........................................................................................... 81
12.10.6. OFFSET (Window offset) ............................................................................ 81
12.10.7. ED (Dynamic reading count-by) .................................................................. 82
12.10.8. MODE (Capture mode) ............................................................................... 82
12.10.9. IN.STRT (Capture start input) ..................................................................... 82
12.10.10. IN.MID (Mid capture input) .......................................................................... 82
12.10.11. IN.END (End capture input) ........................................................................ 82
12.10.12. GROUP (Axle group time) .......................................................................... 82
12.10.13. DYN.SCL (Dynamic reading scaling factor) ................................................ 83
12.10.14. I/LOCK (Truck weighing interlock) ..............................................................
83
12.10.15. IL.TIME (Truck weighing interlock time) ...................................................... 83
12.10.16. USE IO ........................................................................................................ 83
12.11. End (Save and exit) ..................................................................................................... 83
13. CALIBRATION ....................................................................................................................... 84
13.1. Performing a Digital Calibration with Test Weights ..................................................... 84
13.1.1. ZERO (Zero Calibration Routine) ................................................................ 85
13.1.2. SPAN (Span Calibration Routine) ............................................................... 86
13.2. Performing a Calibration with Direct mV/V Entry ........................................................ 86
13.2.1. DIR.ZER (Direct Zero Calibration Entry) ..................................................... 86
13.2.2. DIR.SPN (Direct Span Calibration Entry) .................................................... 86
13.3. Using Linearisation ...................................................................................................... 88
13.3.1. ED.LIN (Edit Linearisation Points) .............................................................. 89
13.3.2. CLR.LIN (Clear Linearisation) ..................................................................... 89
13.4. Calibration Errors ........................................................................................................ 90
14. NETWORK COMMUNICATIONS ........................................................................................... 91
14.1. Introduction .................................................................................................................
91
14.2. Network Protocol RINCMD ......................................................................................... 91
14.2.1. Basic Message Format ............................................................................... 91
14.2.2. Termination ................................................................................................. 92
14.2.3. Error Handling ............................................................................................. 93
14.2.4. Ring Network Enhancement ....................................................................... 93
14.2.5. Calibrating an instrument over a network ................................................... 93
14.3. Network Protocol SIMPLE ........................................................................................... 94
14.4. Network Protocol BARCODE (K404 and K405 only) .................................................. 95
14.5. Network Protocol LUA BUFFER (K422 only) .............................................................. 95
14.6. rinCMD Examples ....................................................................................................... 96
15. AUTOMATIC WEIGHT OUTPUT ........................................................................................... 98
15.1. Overview ..................................................................................................................... 98
15.2. Auto Weight Format String .......................................................................................... 98
16. PRINTING ............................................................................................................................. 100
16.1. Overview ................................................................................................................... 100
16.2. Print ID ......................................................................................................................
100
16.3. Docket printouts ........................................................................................................ 100
16.3.1. Docket Formats ......................................................................................... 100
16.3.2. Custom Docket Events ............................................................................. 103
16.4. Report printouts ......................................................................................................... 104
16.5. Custom Printing ......................................................................................................... 104
16.5.1. Page Tokens ............................................................................................. 106
17. SETPOINTS ......................................................................................................................... 107
17.1. Overview ................................................................................................................... 107
17.2. Outputs ...................................................................................................................... 107
17.3. Common Settings ...................................................................................................... 107
17.4. Weigh in (OVER) Setpoints and Weigh Out (UNDER) Setpoints ............................. 108
To Next Page
Loading...
