Rohde & Schwarz SMW-K144 - PUSCH UCI Commands

Remote-Control Commands
R&S
®
SMW-K144
210User Manual 1178.8013.02 ─ 06
Parameters:
<UseScramblingId> 0 | 1 | OFF | ON
*RST: 0
Example: See Example "Configuring the PUSCH settings" on page 159.
Manual operation: See "Use PUSCH Scrambling ID" on page 77
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:
PUSCh:DSID <DataScrambleId>
If [:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:
PUSCh:SCRambling:STATe 1, sets the data scrambling ID.
Parameters:
<DataScrambleId> integer
Range: 0 to 1023
*RST: 0
Example: See Example "Configuring the PUSCH settings" on page 159.
Manual operation: See "Data Scrambling ID" on page 77
8.10.6 PUSCH UCI Commands
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:STATe........210
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:MODE........211
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:ALPHa....... 211
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:HARQ:
OFF0..................................................................................................................211
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:HARQ:
OFF1..................................................................................................................211
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:HARQ:
OFF2..................................................................................................................211
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:CSI:OF10...212
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:CSI:OF11... 212
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:CSI:OF20...212
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:CSI:OF21...212
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:UCI:
STATe <UCIState>
Enables the transmission and the configuration of the uplink control information (UCI).
Parameters:
<UCIState> 0 | 1 | OFF | ON
*RST: 0
Example: See Example "Configuring the PUSCH settings" on page 159.
Manual operation: See "State" on page 78
BWP Configuration Commands