Rohde & Schwarz SMW-K144 - PRACH Commands

Remote-Control Commands
R&S
®
SMW-K144
253User Manual 1178.8013.02 ─ 06
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:
BWPart<gr0>:ALLoc<user0>:PUCCh:PL:UCI:PATTern <PucchUciPattern>,
<BitCount>
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:
BWPart<gr0>:ALLoc<user0>:PUCCh:PL:ACK:PATTern <AackPattern>,
<Bitcount>
Sets the ACK/UCI bits in pattern form.
Parameters:
<AackPattern> numeric
Bit pattern
*RST: #H0
<Bitcount> integer
Pattern length, should be the same as the length set with the
command [:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:
SUBF<st0>:USER<dir0>:BWPart<gr0>:ALLoc<user0>:
PUCCh:PL:ACK:BITS.
Range: 1 to 128
*RST: 0
Example: See Example "Configuring the PUCCH settings" on page 161.
Manual operation: See "ACK Pattern" on page 121
8.15 PRACH Commands
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:SCSPacing........................................................................253
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:FORMat............................................................................ 254
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:RSET................................................................................254
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:RSEQuence...................................................................... 254
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:ZCZone.............................................................................255
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:PRINdex........................................................................... 255
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PRACh:RBNumber?.......................................................................255
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:
BWPart<gr0>:ALLoc<user0>:PRACh:SCSPacing <PrachNumerology>
Selects a combination of the subcarrier spacing (SCS) and the cyclic prefix (CP) for
PRACH.
PRACH Commands