PR 5610 Installation Manual List of Contents
Sartorius 3
4.10.5 Function 6: Write a word ......................................................................................................................... 103
4.10.6 Function 8: Diagnosis .............................................................................................................................. 104
4.10.7 Function 15: write n successive bits......................................................................................................... 104
4.10.8 Function 16: write n successive words..................................................................................................... 105
4.10.9 MODBUS / J-BUS error messages........................................................................................................... 105
4.10.10 MODBUS / J-BUS Addresses .................................................................................................................. 106
5 COMMISSIONING WITH TERMINAL.......................................................................................................... 107
5.1 SYSTEM CONSOLE: CONNECTING MENU STRUCTURE........................................................................................... 107
5.1.1 Connecting PR 5610 to PC....................................................................................................................... 107
5.1.2 Terminal program..................................................................................................................................... 107
5.1.3 Main-Command-Level menu structure.................................................................................................... 108
5.1.4 General operating notes ........................................................................................................................... 110
5.2 CONFIGURATION ................................................................................................................................................ 111
5.2.1 Set date ..................................................................................................................................................... 111
5.2.2 Set time ..................................................................................................................................................... 112
5.2.3 Serial port setup........................................................................................................................................ 112
5.2.4 Entry of software licence numbers............................................................................................................ 114
5.2.5 Entry of software parameters ................................................................................................................... 115
5.2.6 Fieldbus parameter................................................................................................................................... 116
5.2.7 Entry of user-defined units........................................................................................................................ 117
5.2.8 Printing all configuration data................................................................................................................. 117
5.3 WEIGHING POINT MASK...................................................................................................................................... 118
5.3.1 Weighing point assignment....................................................................................................................... 119
5.4 WEIGHING POINT PARAMETERS: STORING, SAVING, PROTECTING....................................................................... 119
5.4.1 Access protection: CAL-switch................................................................................................................. 119
5.4.2 Saving the weighing point parameters in EAROM................................................................................... 121
5.5 INTERNAL ADC, PARAMETERS........................................................................................................................... 122
5.5.1 Editing functions for parameter entry ...................................................................................................... 122
5.5.2 Filter: Analog Filter ................................................................................................................................. 123
5.5.3 Analog test mode: Testmode..................................................................................................................... 123
5.5.4 Measuring time: Meastime ....................................................................................................................... 123
5.5.5 Standstill detection.................................................................................................................................... 123
5.5.6 Zero set range: Zeroset.rn ........................................................................................................................ 123
5.5.7 Automatic zero tracking............................................................................................................................ 124
5.5.8 Automatic zero correction switch-on/off................................................................................................... 124
5.5.9 Zero tracking range: Zerotrk.rn ............................................................................................................... 124
5.5.10 Zero tracking stepwidth: Zerotrk.st .......................................................................................................... 124
5.5.11 Zero tracking interval: Zerotrk.ti.............................................................................................................. 124
5.5.12 Multirange scale....................................................................................................................................... 124
5.5.13 Tare time-out: Tare timot ......................................................................................................................... 124
5.5.14 Maximum permissible overload: Overload .............................................................................................. 125
5.5.15 Min. weight limit for print-out: no p below .............................................................................................. 125
5.5.16 Stepwidth (scale divisions): Stepwidth...................................................................................................... 125
5.5.17 W&M mode: W & M.................................................................................................................................. 125
5.6 WEIGHING POINT CALIBRATION.......................................................................................................................... 126
5.6.1 Calibration data........................................................................................................................................ 126
5.6.2 Editing functions for parameter entry ...................................................................................................... 127
5.6.3 Adjusting the full scale value: Fullscale................................................................................................... 127
5.6.4 Default span.............................................................................................................................................. 128
5.6.5 Weighing point calibration procedure / sequence.................................................................................... 128
5.6.6 Weighing point calibration with weights.................................................................................................. 128
5.6.7 Weighing point calibration without weights............................................................................................. 131
5.6.8 Error messages in the calibration menu................................................................................................... 134
5.6.9 Liquid counter........................................................................................................................................... 135
5.6.10 Customer-specific weighing point (user).................................................................................................. 136
5.6.11 GWT Scale ................................................................................................................................................ 138
5.6.12 Sartorius scale (xBPI)............................................................................................................................... 139
5.7 SUB-MENU SERVICE ........................................................................................................................................... 140
5.7.1 Available memory in PR 5610 .................................................................................................................. 140
5.7.2 Show hardware configuration .................................................................................................................. 141
5.7.3 Testing the input and output modules....................................................................................................... 141
To Next Page
Loading...