SATO WS4 Series - Page 190

184
No
Item
Valid selection
a
Print method (WS408TT/WS412TT only)
Default value: 01H
00H Direct thermal
01H Thermal transfer
b
Reserved
00H Fixed
c
Print speed
203dpi Default value: 02H
305dpi Default value: 02H
00H 2ips
01H 3ips
02H 4ips
d
Print mode
(Default value: 01H)
00H Continuous
01H Tear off
02H Cutter
03H Dispenser
04H Nonesepa (Linerless)
e
Cutter mode
(Default value: 00H)
00H Motion 1 (Head position)
01H Motion 2 (Cut position)
02H Motion 3 (No backfeed)
f
Dispenser mode
(Default value: 00H)
00H Motion 1 (Head position)
01H Motion 2 (Dispense position)
g
Nonesepa mode
(Default value: 00H)
00H Motion 2 (Tear off position)
01H Motion 3 (No backfeed)
h
Print darkness:
(Default value: 41H)
41H A
h
Print darkness level
(Default value: 03H)
01H Level 1
02H Level 2
03H Level 3
04H Level 4
05H Level 5
i
Sensor type
(Default value: 01H)
00H Reflective
01H Transmissive
02H Sensor off
04H Transmissive sensor (CX compatible)
j
0 Slash
(Default value: 01H)
00H Disabled
01H Enabled
k
Kanji code
(Default value: 00H)
00H JIS Code
01H Shift JIS code
l
Reserved
00H Fixed
m
Initial feed
(Default value: 00H)
00H Disabled
01H Enabled
n
Character pitch
(Default value: 01H)
00H Fixed
01H Proportional
o
Label height (dot)
203dpi Default value: 0960H
305dPi Default value: 0E10H
WS408
[0001H ~ 0960H] (1 to 2400)
WS412
[0001H ~ 0E10H] (1 to 3600)
p
Label width (dot)
203dpi Default value: 0340H
305dPi Default value: 04E0H
WS408
[0001H ~ 0340H] (1 to 832)
WS412
[0001H ~ 04E0H] (1 to 1248)
q
Vertical base point correction (dot)
(specifying in 2 bytes)
(Default value: 000H)
[0000H - 012CH] (0 to 300)
[FFFFH - FED4H] (-1 to -300)
r
Horizontal base point correction (dot)
(specifying in 2 bytes)
(Default value: 000H)
[0000H - 012CH] (0 to 300)
[FFFFH - FED4H] (-1 to -300)
s
Vertical pitch offset (dot)
(Default value: 00H)
[00H - 63H] (0 to 99)
[FFH - 9DH] (-1 to -99)
t
TearOff position offset(dot)
(Default value: 00H)
[00H - 63H] (0 to 99)
[FFH - 9DH] (-1 to -99)
u
Cut position offset (dot)
(Default value: 00H)
[00H - 63H] (0 to 99)
[FFH - 9DH] (-1 to -99)
v
Dispensing position offset (dot)
(Default value: 00H)
[00H - 63H] (0 to 99)
[FFH - 9DH] (-1 to -99)
w
Control code
(Default value: 00H)
00H Standard code
01H Non-standard code
x
Gap between labels (dot)
203dpi Default value: 18H
305dpi Default value: 24H
[08H - 40H] (8 to 64) 203dpi
[0CH - 60H] (12 to 96) 305dpi