Siemens SINUMERIK 808D ADVANCED - Page 214

Programming and Operating Manual (Milling)
214 6FC5398-4DP10-0BA1, 01/2014
N10 SUPA G00 Z300 D0
N15 SUPA G00 X300 Y300
N20 T1 D1
N25 MSG ("Please change to Tool No 1")
N30 M05 M09 M00
N35S4000 M3
N40 CYCLE71 ( 50.00000, 2.00000, 2.00000, 0.00000, 0.00000, 0.00000, 70.00000, 100.00000,
0.00000, 2.00000, 40.00000, 2.00000, 0.20000, 500.00000, 41, 5.00000)
N45 S4500 M3
N50 CYCLE71(50,2,2,0,0,0,70,100,0,2,40,2,0.2,300,22,5)
N55 SUPA G00 Z300 D0
N60 SUPA G00 X300 Y300
N65 T3 D1
N70 MSG ("Please change to Tool No 3")
N75 M05 M09 M00
N80 S5000 M3 G94 F300
N85 G00 X-6 Y92
N90 G00 Z2
N95 G01 F300 Z-10
N100 G41 Y 90
N105 G01 X10 RND=5
N110 G01 Y97 CHR=2
N115 G01 X70 RND=4
N120 G01 Y90
N125 G01 G40 X80
N130 G00 Z50
N135 SUPA G00 Z300 D0
N140 SUPA G00 X300 Y300
N145 T4 D1
N150 MSG("Please change to Tool No 4")
N155 M05 M09 M00
N160 S5000 M3
N165 POCKET4 ( 50.00000, 0.00000, 2.00000, -5.00000, 22.00000, 38.00000, 70.00000,
2.50000, 0.20000, 0.20000, 300.00000, 250.00000, 0, 21, 10.00000, 0.00000, 5.00000,
2.00000, 0.50000)
N170 S5500 M3
N175 POCKET4 ( 50.00000, 0.00000, 2.00000, -5.00000, 22.00000, 38.00000, 70.00000,
2.50000, 0.20000, 0.20000, 250.00000, 250.00000, 0, 22, 10.00000, 0.00000, 5.00000,
2.00000, 0.50000)
N180 SUPA G00 Z300 D0
N185 SUPA G00 X300 Y300
N190 T5 D1
N195 MSG("Please change to Tool No 5")
N200 M05 M09 M00
N205 S7000 M3
N210 SLOT2( 50.00000, 0.00000, 2.00000, -5.00000, 2.00000, 3, 30.00000, 6.00000, 38.00000,
70.00000, 20.00000, 165.00000, 90.00000, 300.00000, 300.00000, 3.00000, 3, 0.20000, 2000,
5.00000, 250.00000, 8000.00000, )
N215 SUPA G00 Z300 D0
N220 SUPA G00 X300 Y300
N225 T2 D1
N230 MSG("Please change to Tool No 2")