Chapter 40 Access Control
MES3500 Series User’s Guide
307
externalalar
m
ExternalAlarmEventOn 1.3.6.1.4.1.890.1.5.8.68.27.2.1
1.3.6.1.4.1.890.1.5.8.57.27.2.1
1.3.6.1.4.1.890.1.5.8.80.27.2.1
This trap is sent when the external alarm is
received.
ExternalAlarmEventClear 1.3.6.1.4.1.890.1.5.8.68.27.2.2
1.3.6.1.4.1.890.1.5.8.57.27.2.2
1.3.6.1.4.1.890.1.5.8.80.27.2.2
This trap is sent when the external alarm
stops sending an alert.
dyinggasp DyingGaspEventOn 1.3.6.1.4.1.890.1.5.8.68.27.2.1
1.3.6.1.4.1.890.1.5.8.57.27.2.1
1.3.6.1.4.1.890.1.5.8.80.27.2.1
The trap is sent when the device power goes
below the normal value.
Table 143 SNMP System Traps (continued)
OPTION OBJECT LABEL OBJECT ID DESCRIPTION
Table 144 SNMP Interface Traps
OPTION OBJECT LABEL OBJECT ID DESCRIPTION
linkup linkUp 1.3.6.1.6.3.1.1.5.4 This trap is sent when the Ethernet link is
up.
LinkDownEventClear 1.3.6.1.4.1.890.1.5.8.68.27.2.2
1.3.6.1.4.1.890.1.5.8.57.27.2.2
1.3.6.1.4.1.890.1.5.8.80.27.2.2
This trap is sent when the Ethernet link is
up.
linkdown linkDown 1.3.6.1.6.3.1.1.5.3 This trap is sent when the Ethernet link is
down.
LinkDownEventOn 1.3.6.1.4.1.890.1.5.8.68.27.2.1
1.3.6.1.4.1.890.1.5.8.57.27.2.1
1.3.6.1.4.1.890.1.5.8.80.27.2.1
This trap is sent when the Ethernet link is
down.
lldp LLDPRemoteTopologyChange 1.0.8802.1.1.2.0.0.1 This trap is sent when the LLDP (Link Layer
Discovery Protocol) remote topology
changes.
transceiver
-ddmi
transceiverddmiEventOn 1.3.6.1.4.1.890.1.5.8.68.27.2.1
1.3.6.1.4.1.890.1.5.8.57.27.2.1
1.3.6.1.4.1.890.1.5.8.80.27.2.1
This trap is sent when one of the device
operating parameters (such as transceiver
temperature, laser bias current,
transmitted optical power, received optical
power and transceiver supply voltage) is
above or below a factory set normal range.
transceiverddmiEventClear 1.3.6.1.4.1.890.1.5.8.68.27.2.2
1.3.6.1.4.1.890.1.5.8.57.27.2.2
1.3.6.1.4.1.890.1.5.8.80.27.2.2
This trap is sent when all device operating
parameters return to the normal operating
range.