5
Unpacking and Preparation
4.4 <LIST SWEEP DISPLAY> Page
*Not available in AT2817
......................................................................... 29
4.4.1 Sweep Trigger Mode [TRIG] ................................................................................................... 29
5. [Setup] Key ...................................................................................................................................................... 31
5.1 <MEAS SETUP> Page .................................................................................................................... 31
5.1.1 Source Output Impedance [SRC RES] .................................................................................... 32
5.1.2 Averaging Factor [AVG] .......................................................................................................... 32
5.1.3 DC Bias Voltage Monitor {Option} ......................................................................................... 32
5.1.4 Auto LCZ Function [AUTO LCZ] .......................................................................................... 32
5.1.5 Monitor 1 and Monitor 2 [MON 1][MON 2] ........................................................................... 33
5.2 <CORRECTION> Page ................................................................................................................... 33
5.2.1 Open correction [OPEN] ......................................................................................................... 34
5.2.2 Short Correction [SHORT] ...................................................................................................... 35
5.2.3 Frequency 1, 2, 3 Correction [FREQ 1] [FREQ 2] [FREQ3] .................................................. 36
5.3 <LIMIT TABLE SETUP> Page ...................................................................................................... 37
5.3.1 Comparator Function ON/OFF ................................................................................................ 38
5.3.2 Auxiliary Bin [AUX] ............................................................................................................... 39
5.3.3 Primary Parameter Comparator limit mode [MODE] .............................................................. 39
5.3.4 Nominal value for tolerance mode ........................................................................................... 41
5.3.5 Beep feature ............................................................................................................................. 41
5.3.6 Beep Tone [TONE] .................................................................................................................. 41
5.3.7 Total Number of Bins [#-BINS] .............................................................................................. 41
5.3.8 Lower and Upper Limits .......................................................................................................... 42
5.4 <LIST SWEEP SETUP> Page
*Not available in AT2817
............................................................................ 42
5.4.1 Sweep Trigger Mode [TRIG] ................................................................................................... 43
5.4.2 List Sweep Parameters ............................................................................................................. 43
5.4.3 Sweep Point and Limit Modes ................................................................................................. 44
6. System Configurations..................................................................................................................................... 45
6.1 <SYSTEM CONFIG> Page ............................................................................................................ 45
6.1.1 System Language [LANGUAGE] ........................................................................................... 45
6.1.2 Setting the system date and time .............................................................................................. 46
6.1.3 Account Setting ....................................................................................................................... 46
6.1.4 Beep Feature ............................................................................................................................ 47
6.1.5 Beep Tone [TONE] .................................................................................................................. 47
6.1.6 RS-232 Baud Rate ................................................................................................................... 47
6.2 <SYSTEM INFO> Page .................................................................................................................. 48
7. File Operation .................................................................................................................................................. 49
7.1 <CATALOG> Page .......................................................................................................................... 49
7.1.1 Recall a File at Startup [AUTO RECALL] .............................................................................. 49
7.1.2 Auto save data to last file [AUTO SAVE] ............................................................................... 50
7.1.3 File operation ........................................................................................................................... 50
8. Handler Interface ............................................................................................................................................. 51
8.1 Pin Assignment ................................................................................................................................ 51
8.2 Power Rating ................................................................................................................................... 52
8.3 Electrical Characteristics ................................................................................................................. 53
8.3.1 Input Signal: ............................................................................................................................. 53
8.3.2 Output Signal: .......................................................................................................................... 53
8.3.3 Power supply ........................................................................................................................... 53
8.3.4 Schematic ................................................................................................................................. 53
8.4 Timing Chart .................................................................................................................................... 54
9. Examples ......................................................................................................................................................... 56
9.1 Basic Measurement Procedure ......................................................................................................... 56
9.2 Example ........................................................................................................................................... 57
10. Remote Control ........................................................................................................................................ 59
10.1 About RS-232C ............................................................................................................................... 59
10.2 About USB-Serial Interface (Option) .............................................................................................. 59
10.3 To Select Baud Rate ......................................................................................................................... 60
10.4 About USB-Serial Interface ............................................................................................................. 60
10.4.1 Installing USB-Serial drivers on Windows XP ........................................................................ 60
10.4.2 Installing AT281X Serial_Port_Debug Software ..................................................................... 63
10.5 SCPI Language ................................................................................................................................ 64
To Next Page
Loading...
