What does 'Overspeed error' mean on my Atlas Copco Tools wrench?
If the Atlas Copco Tools wrench displays 'Overspeed error', it indicates the tightening operation was executed too quickly, and the angle result is set to 9999 degrees. Repeat the tightening, operating the wrench more slowly.
What does it mean if my Atlas Copco STwrench Tools wrench shows a 'Communication error' when sending a Pset?
If the Atlas Copco Tools wrench displays 'Communication error' when a Pset is sent, it means the Pset contains an angle parameter, but the smartHEAD lacks a gyroscope. The suggested solution is to use a Pset with only a torque strategy or use a smartHEAD equipped with a gyroscope.
Why does my Atlas Copco STwrench wrench display 'Insert Tool' when starting a Pset?
If the Atlas Copco Tools wrench displays 'Insert Tool' when starting a Pset, it's likely because the tool recognition function is enabled, but the tool in use doesn't have the RFID TAG, or the RFID TAG inside the end-fitting tool isn't working. If you want to use an end-fitting tool or an extension without the RFID TAG, disable the tool recognition function. Alternatively, replace the end-fitting tool or disable the tool recognition function.
What should I do if my Atlas Copco Tools wrench shows 'Error Zeroing Gyro'?
If the Atlas Copco Tools wrench displays 'Error Zeroing Gyro', it could be due to bad wrench handling during power on, gyroscope failure, or controller failure. Try switching the wrench off and then on again, keeping it in a fixed position during the zero adjustment. If the problem continues, replace the smartHEAD or the wrench controller to see if that solves the issue.
What to do if I see 'Error Zeroing Torque' on my Atlas Copco STwrench wrench display?
If the Atlas Copco Tools wrench displays 'Error Zeroing Torque', it could be due to bad wrench handling during power on, a yielded transducer, or controller failure. Try switching off the wrench, then switch it back on, ensuring no torque is applied during zero adjustment. If the issue persists, consider replacing the smartHEAD or the wrench controller to see if that resolves the problem.
Why does my Atlas Copco STwrench Tools wrench display 'No program'?
If your Atlas Copco Tools wrench displays 'No program', this indicates a missing Pset. This could be because the tool recognition is used to select a program, but there is no Pset associated with the current end-fitting tool number plugged into the smartHEAD. It could also mean that the barcode is used to select a program, but there is no Pset associated with the barcode reader. To resolve this, you can: * Define at least one Pset in the wrench. * Define a Pset associated with the end-fitting tool currently installed in the smartHEAD. * Define a Pset associated with the barcode currently being read.
What to do if my Atlas Copco Tools wrench displays a 'Memory error'?
If the Atlas Copco Tools wrench displays 'Memory error', try restarting the wrench. If the problem persists, the wrench needs to be repaired.
General| Brand | Atlas Copco |
|---|---|
| Model | STwrench |
| Category | Tools |
| Language | English |
Details the structure of the user guide and its main parts, outlining the scope of each chapter.
Lists the technical and battery pack specifications of the STwrench, including ranges and accuracies.
Outlines the STwrench's conformity with EU directives and applicable normalized standards.
Explains the modular design of the STwrench and its customization through interchangeable components.
Summarizes the tightening strategies available for different STwrench and smartHEAD versions.
Provides an overview of the main applications and connection scenarios for the STwrench.
Details the main components and modules that constitute the STwrench system.
Describes the function of the STwrench's LEDs for guiding operations and signaling results.
Explains the information shown on the STwrench display during menu navigation and operation.
Details the function of each button on the STwrench keyboard for menu browsing and operations.
Guides the user through performing a basic tightening test without pre-programmed settings.
Provides instructions for installing and registering the ToolsTalk BLM software.
Introduces the ToolsTalk BLM interface, including menu list, toolbar, and wrench map.
Explains the procedure for connecting the STwrench to the PC using the ToolsTalk BLM software.
Details the parameters related to torque settings for a tightening program (Pset).
Describes various tightening strategies, categorized into Production and Quality Control.
Defines batch parameters for Multistage execution, including count, size, and lock options.
Guides the user on how to execute a Multistage sequence on the STwrench.
Details the control parameters for a Job, including name, type, and repeat settings.
Explains how to execute a Job sequence on the STwrench.
Explains the concept of identifiers, their types, and usage for selecting programs or data.
Details the process of scanning identifiers using the STwrench for program selection.
Describes how to access and use the STwrench's on-device settings menu.
Covers the configuration settings for the STwrench controller via ToolsTalk BLM.
Details how to access smartHEAD information and TAG number programming.
Explains how to create tightening programs and configurations offline using ToolsTalk BLM.
Guides on transferring created offline files to one or more STwrenches.
Details how to select and view individual tightening traces from the wrench memory.
Explains how to overlap and compare multiple tightening traces.
Describes how to copy, print, or export trace data to PC or image formats.
Covers enabling and configuring the real-time tightening trace display in ToolsTalk BLM.
Details connecting the STwrench to Power Focus using the IRC-B radio module.
Explains connecting the STwrench to Power Focus via the IRC-W radio module.
Describes connecting the STwrench to Power Focus using the STwrench Cable Box.
Provides a cross-reference for Power Focus settings and critical STwrench parameters.
Guides on setting up wireless network parameters for STwrench to ToolsNet communication.
Lists the tightening data points that are sent from the STwrench to ToolsNet.
Details connecting the STwrench to Torque Supervisor via USB or IRC-W module.
Cross-references Torque Supervisor parameters with STwrench Pset parameters.
Explains the process of associating the STwrench with a QATnode via IRDA or IRC-W.
Covers the proper configuration of both STwrench and QATnode for integrated operation.
Details how to configure and print tightening results on a STAR printer via QATnode.
Explains the configuration and use of QATnode's input/output connectors.
Guides on establishing a ToolsNet connection using the QATnode T.
Details how to connect the STwrench to an API via IRC-W module.
Explains how to configure and use Real Time Traces function via IRC-W with API.
Outlines the requirement and procedure for annual STwrench calibration.
Provides instructions for cleaning the STwrench and its components.
Offers guidance on proper battery usage, charging, and long-term storage.
Explains how to use the diagnostic menu for hardware checks and troubleshooting.
Details how to calculate and apply torque correction coefficients for extensions and multipliers.
Explains the procedure for calculating the angle correction coefficient (CCA).
To Next Page
