EasyManuals Logo
Home>AudioCodes>Gateway>MediaPack MP-11 Series

AudioCodes MediaPack MP-11 Series User Manual

AudioCodes MediaPack MP-11 Series
1195 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1074 background imageLoading...
Page #1074 background image
User's Manual 1074 Document #: LTRT-27045
Mediant 1000B Gateway & E-SBC
62.10.6 PSTN Parameters
This subsection describes the device's PSTN parameters.
62.10.6.1 General Parameters
The general PSTN parameters are described in the table below.
Table 62-56: General PSTN Parameters
Parameter Description
Trunk Name
config-voip > interface
<e1|t1|bri> name
[DigitalPortInfo_x]
Defines an arbitrary name for a trunk (where x denotes the trunk
number for the ini file parameter). This can be used to help you
easily identify the trunk.
The valid value is a string of up to 40 characters. The following
special characters can be used (without the quotes):
ï‚§ " " (space)
ï‚§ "." (period)
ï‚§ "=" (equal sign)
ï‚§ "-" (hyphen)
ï‚§ "_" (underscore)
ï‚§ "#" (pound sign)
By default, the value is undefined.
Protocol Type
configure voip > interface e1-
t1|bri > protocol
[ProtocolType]
Defines the PSTN protocol for all the Trunks. To configure the
protocol type for a specific Trunk, use the ini file parameter
ProtocolType_x:
ï‚§ [0] NONE
ï‚§ [1] E1 EURO ISDN = ISDN PRI Pan-European (CTR4)
protocol
ï‚§ [2] T1 CAS = Common T1 robbed bits protocols including E&M
wink start, E&M immediate start, E&M delay dial/start and loop-
start and ground start.
ï‚§ [3] T1 RAW CAS
ï‚§ [4] T1 TRANSPARENT = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 24 of all
trunks are mapped to DSP channels.
ï‚§ [5] E1 TRANSPARENT 31 = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 31 of each
trunk are mapped to DSP channels.
ï‚§ [6] E1 TRANSPARENT 30 = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 31,
excluding time slot 16 of all trunks are mapped to DSP
channels.
ï‚§ [7] E1 MFCR2 = Common E1 MFC/R2 CAS protocols
(including line signaling and compelled register signaling).
ï‚§ [8] E1 CAS = Common E1 CAS protocols (including line
signaling and MF/DTMF address transfer).
ï‚§ [9] E1 RAW CAS
ï‚§ [10] T1 NI2 ISDN = National ISDN 2 PRI protocol
ï‚§ [11] T1 4ESS ISDN = ISDN PRI protocol for the
Lucentâ„¢/AT&Tâ„¢ 4ESS switch.
ï‚§ [12] T1 5ESS 9 ISDN = ISDN PRI protocol for the
Lucentâ„¢/AT&Tâ„¢ 5ESS-9 switch.

Table of Contents

Other manuals for AudioCodes MediaPack MP-11 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MediaPack MP-11 Series and is the answer not in the manual?

AudioCodes MediaPack MP-11 Series Specifications

General IconGeneral
BrandAudioCodes
ModelMediaPack MP-11 Series
CategoryGateway
LanguageEnglish

Related product manuals