AUMA Aumatic AC 01.1 User Manual

Index
A
Adaptive behaviour 55
Alarm contact 29
Analogue output 1
feedback signals 32
Analogue output 2
feedback signals 34
Analogue position
feedback signal 33,34
B
Blinker 21,30
Bluetooth interface 12
Bus address 77
C
Collective fault signal 29
COM-AC 12
COM-AC (software) 8
Combination fieldbus/standard
interface 83
Commission number 7
Contrast 14
Control 7
Corrective action 91
D
Dead band 56
Dead time 57
Delay time 43
Derivative gain 64
Diagnostics 95
Display - indications 15
E
Electronic name plate 17
EMERGENCY behaviour 38,40
EMERGENCY operation 38
EMERGENCY position 40
EMERGENCY STOP function 75
End position tolerance 58
External inputs for bus 80
F
Failure behaviour 41,66
Failure delay time 43
Failure functions 84
Failure operation 41,42,44
Failure position 42
Failure source 42,44
Fault signal 25
Faults 91
Feedback signals 31
Feedback signals via output
contacts 27
Functions of the AUMATIC 45
I
I/O stack 2 78,83
Identification 7
Indication lights 19
Indications 15
Infra-red interface 12
Input MODE 58
Input range of process setpoint 69
Input range process variable 69
Intermediate positions 48
Internet 7
Intrusive 8
Inverse operation 66
L
Language change in the display 14
LEDs 19
Limit seating 45
Limit switching 47
Limitation of the travel 67
Local controls 9
Local controls enable function 73
Logging of operating data 95
Loss of the process setpoint 66
M
Max. error variable (outer dead
band) 57
Max. permissible operation time 88
MODE input 58
Monitoring functions 84
Motor protection 85
Motor protection by-pass 40
Multiport valve function 52
N
Name plate 7
Non-Intrusive 8
Non-Intrusive (version) 8
Number of starts 86
O
OFF times 72
ON times 72
Open-close duty
Open-close duty – modulating
duty selection 58
Operating time monitoring 88
Operation 9
Operation mode 35
Operation mode EMERGENCY 38
Operation mode FAILURE 41
Operation mode LOCAL 36
Operation mode OFF 35
Operation mode REMOTE 37
Operation mode
SETPOINT MODE 55
Output contacts 27
Overrun (inner dead band) 56
P
Password change 13
Password entry 11
Percent/per mil change-over 26
Phase failure monitoring 90
Position feedback signals 31
Position transmitter 31
Positioner 55
Preset position 43
Process controller 61
Process representation input 22
Process setpoint, internal 65
Profibus DP interface 77
Profibus DP-V1 services 79
Proportional gain 63
PTC thermistors 85
Push-to-run operation 9,36,37
R
Range of application 6
Rate time 64
Reaction monitoring 68,89
Reaction of actuator 39,42
Reset time 63
Running indication 19,21,30
Running time per hour 86
Running time, max. permissible 87
S
Safety instructions 5
Self-retaining 9,36,37
Setpoint E1
Input range 60
Source 59
Short description 8
Signals 22
Signals via fieldbus 22
Size 7
Slave address 77
Source for initiation 42,44
Status indication 15
Stepping mode 70
Stepping range 71
T
Thermoswitches 85
Torque by-pass 84
Torque E6 32
Torque feedback signal 33
Torque indication 16
Torque monitoring 84
Torque seating 45
Torque switching by-pass 40
Type 7
Type of seating 45
V
Valve position 15
W
Warnings 91
Wiring diagram (name plate) 7
108
Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Profibus DP Manual

AUMA Aumatic AC 01.1 Specifications

General

Brand	AUMA
Model	Aumatic AC 01.1
Category	Control Unit
Language	English