AUMA Aumatic AC 01.1 User Manual

Table of contents Page
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 General notes regarding safety 5
1.2 Range of application 6
1.3 Warnings and symbols 6
2 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Name plate 7
2.2 Short description 8
3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3.1 Local operation 9
3.2 Operation from REMOTE 9
3.3 Menu navigation via push buttons (for settings and indications) 10
3.3.1 Short overview: functions of the push buttons 10
3.3.2 Structural design and navigation 11
3.4 Operation and setting via AUMA COM-AC programming software 12
3.4.1 Operation setting via COM-AC 12
3.5 Password change 13
3.6 Language change in the display 14
3.7 LCD contrast setting of the display (applies only to controls with green display) 14
4 Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1 Status indications in the display 15
4.1.1 Status indication S0/S6 – operation 15
4.1.2 Status indication S4 – torque 16
4.2 Torque indication: edit 16
4.3 Electronic name plate 17
4.3.1 Display indication: enable view 17
4.3.2 Electronic name plate: view 17
4.4 Indication lights/LEDs 19
4.4.1 Standard indication 19
4.4.2 Configuration of the signals: view/edit 20
4.4.3 Blinking behaviour of indication lights/LEDs: view/edit 21
5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5.1 Signals via fieldbus 22
5.1.1 Configuration for process representation input: view 22
5.1.2 Configuration of adjustable (user-definable) signals: view 23
5.1.3 Configuration of fault signals: view 25
5.1.4 Percent/per mil coding for transmission values: view 26
5.2 Feedback via output contacts (binary) - (option) 27
5.2.1 Configuration for output contacts 1 to 5: view/edit 27
5.2.2 Configuration for alarm contacts (collective fault signal): view/edit 29
5.2.3 Output contacts 1 to 5: use as running indication (blinker) 30
5.3 Feedback signals (analogue) - (option) 31
5.3.1 Position transmitter/actual position source (E2): view 31
5.3.2 Source of the torque signal E6: view 32
5.3.3 Feedback signals (configuration) via analogue output 1: view 32
2
Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Profibus DP Manual
Read operation instructions first
.
Observe safety instructions.
Reference documents:
.
Operation instructions (assembly, operation, commissioning) for actuator
.
Manual (Fieldbus device integration) AUMATIC AC 01.1/ACExC 01.1 Profibus DP
Can be downloaded from the Internet (www.auma.com) or ordered directly from AUMA (addresses from page ).

AUMA Aumatic AC 01.1 Specifications

General

Brand	AUMA
Model	Aumatic AC 01.1
Category	Control Unit
Language	English