Biolight Meditech P1

To Next Page

To Previous Page

P1 Patient Monitor User’s Manual

11-4



displayed in the Temp parameter

area.

the probe is tightly connected to the extension cable.

2. Try using a known good probe in case the sensor is

damaged

Main Page

Default Chapter5
- Table of Contents5
Chapter 1 General Introduction10
- Intended Use10
- Composition10
- Contraindications11
- Measurement Modules (When Using with Docking Station)12
- Appearance12
- Applied Parts18
- Installation18
- P1 in Use with a Host Monitor19
- Input Device21
- Printing Device21
- Screen Display21
Chapter 2 Safety27
- Safety Information27
- Equipment Symbols29
- Packaging Symbols30
Chapter 3 Basic Operations31
- Installation31
- Getting Started33
- Operation and Browse34
- General Settings36
- Measurement Settings38
- Operation Mode39
- Using the Timer45
- Using the External Display46
- Shutting off the Monitor47
Chapter 4 Patient Management49
- Discharging a Patient49
- Admitting a Patient50
- Managing Patient Information50
- Transferring Patient Data51
- Connecting to a Central Monitoring System52
Chapter 5 Managing Configurations54
- Introduction54
- Selecting Default Configuration54
- Saving Current Settings54
- Deleting a Configuration55
- Transferring a Configuration55
- Loading Current Configuration56
- New Patient Usage Configuration56
- Monitor Boot Usage Configuration57
- Setting Password Valid Time57
Chapter 6 User Interface58
- Interface Style58
- Dynamic Trend Screen59
- Oxycrg Screen60
- Other Bed Observation61
- Big Font Screen65
- Freezing Waveforms65
- Spo Screen66
Chapter 7 Alarm69
- Introduction69
- Safety Information69
- About the Alarm70
- Viewing Physiological Alarms List72
- Viewing Technical Alarms List72
- Viewing the Graphical Display of Technical Alarms (Alarm View)72
- Setting Alarm73
- Alarm Pause78
- Alarm Reset79
- Latching Alarms80
- Nurse Call81
- Intubation Status82
- Other Bed Alarm83
- Detecting Alarm84
- Actions When an Alarm Occurs85
Chapter 8 ECG86
- Introduction86
- Safety Information86
- ECG Display87
- Preparing for ECG Monitoring88
- ECG Settings94
- Arrhythmia Monitoring100
- ST Monitoring103
- Qt/Qtc Monitoring110
- Isoelectric Segments115
- ECG Relearning115
- Calibrating ECG115
- Defibrillation Synchronization116
- ECG Troubleshooting117
Chapter 9 Respiration Rate (RESP)119
- Introduction119
- Safety Information119
- RESP Display120
- RESP Settings122
- RESP Troubleshooting124
Chapter 10 Spo125
- Introduction125
- Safety Information125
- Spo Measurement Limitations126
- Spo Display127
- Spo Module129
- Monitoring Procedure129
- Setting Spo130
- Setting PR136
- Spo 2 Troubleshooting137
Chapter 11 Temperature（Temp139
- Introduction139
- TEMP Display139
- Preparing for TEMP Monitoring140
- TEMP Settings140
- TEMP Troubleshooting141
Chapter 12 NIBP143
- Introduction143
- Safety Information143
- NIBP Measurement Limitations145
- Measurement Modes145
- NIBP Display146
- Preparing for NIBP Measurements147
- Starting and Stopping NIBP Measurements148
- Viewing the Dynamic Blood Pressure Analysis149
- NIBP Settings149
- Assisting Venous Puncture152
- NIBP Maintenance152
- NIBP Troubleshooting153
Chapter 13 IBP154
- Introduction154
- Safety Information154
- IBP Measurement155
- IBP Display157
- Setting IBP158
- Calculating Cerebral Perfusion Pressure162
- IBP Troubleshooting162
Chapter 14 Carbon Dioxide (CO )164
- Introduction164
- Safety Information164
- CO Measurement Limitations165
- Monitoring Procedure165
- Display172
- Settings CO173
- Entering Intubation Status175
- Zeroing176
- Calibration177
- Exhaust Emission177
- Announcements178
- CO Troubleshooting179
Chapter 15 Review181
- Review Overview181
- Reviewing Page181
Chapter 16 Calculations191
- Introduction191
- Safety Information191
- Drug Calculation191
- Hemodynamic Calculations194
- Oxygenation Calculation196
- Ventilation Calculations199
- Nephridium Calculation201
Chapter 17 Other Functions204
- Analog Signal Output204
- Network Settings204
- Network Printing208
Chapter 18 Battery214
- Introduction214
- Installing a Battery214
- Charging the Bettery215
- Battery Guidelines215
- Battery Maintenance216
- Battery Recycling217
Chapter 19 Maintenance and Cleaning218
- Introduction218
- Cleaning the Monitor and Other Mounting Accessories219
- Disinfecting the Monitor and Other Mounting Accessories219
- Cleaning and Sterilizing of Accessories220
- Sterilization221
Chapter 20 Maintenance222
- Inspection222
- Maintenance Schedule223
- Checking the Version Information224
- Disposing of the Monitor224
Chapter 21 Accessories226
- Recommended Accessories227
Appendix A Product Specifications233
- Safety Specifications233
- Environmental Specifications234
- Physical Specifications234
- Power Specifications235
- Hardware Specifications236
- Data Storage239
- Wireless Network239
- Measurement Specifications240
- Alarm Specification258
Appendix B EMC and Radio Regulatory Compliance261
- Emc261
- The Management Compliance of Radio267
Appendix C Default Settings268
- ECG, Arrhythmia, ST and QT Default Settings268
- RESP Default Settings271
- Spo Default Settings271
- TEMP Default Settings272
- NIBP Default Settings273
- IBP Default Settings274
- CO Default Settings277
- Alarm Default Settings278
- Screen Setup Default Settings279
- Color of Parameters Default Settings279
- Other Default Settings279
- Maintenance Item Default Settings280
Appendix D Alarm Message281
- Physiological Alarm281
- Technical Alarm283
Appendix E Cybersecurity292
- Operating Environment292
- Network Data Interface292
- User Access Control Mechanism292
- Software Environment293
Appendix F Terminology and Definitions294
- List of Units294
- Symbol List295
- Terminology List296
Appendix G Toxic and Harmful Substances or Elements301

Biolight Meditech P1 - Page 142

Table of Contents