Biolight Meditech P1

To Next Page

To Previous Page

P1 Patient Monitor User’s Manual

4-5



For more information on the CMS, refer to the Central Monitoring System’s

instructions for use. For more information about connection of monitor and CMS, refer to

the 17.2.5 Connecting the Central Monitoring System (CMS) in this manual.

Main Page

Default Chapter5
- Table of Contents5
Chapter 1 General Introduction10
- Intended Use10
- Composition10
- Contraindications11
- Measurement Modules (When Using with Docking Station)12
- Appearance12
- Applied Parts18
- Installation18
- P1 in Use with a Host Monitor19
- Input Device21
- Printing Device21
- Screen Display21
Chapter 2 Safety27
- Safety Information27
- Equipment Symbols29
- Packaging Symbols30
Chapter 3 Basic Operations31
- Installation31
- Getting Started33
- Operation and Browse34
- General Settings36
- Measurement Settings38
- Operation Mode39
- Using the Timer45
- Using the External Display46
- Shutting off the Monitor47
Chapter 4 Patient Management49
- Discharging a Patient49
- Admitting a Patient50
- Managing Patient Information50
- Transferring Patient Data51
- Connecting to a Central Monitoring System52
Chapter 5 Managing Configurations54
- Introduction54
- Selecting Default Configuration54
- Saving Current Settings54
- Deleting a Configuration55
- Transferring a Configuration55
- Loading Current Configuration56
- New Patient Usage Configuration56
- Monitor Boot Usage Configuration57
- Setting Password Valid Time57
Chapter 6 User Interface58
- Interface Style58
- Dynamic Trend Screen59
- Oxycrg Screen60
- Other Bed Observation61
- Big Font Screen65
- Freezing Waveforms65
- Spo Screen66
Chapter 7 Alarm69
- Introduction69
- Safety Information69
- About the Alarm70
- Viewing Physiological Alarms List72
- Viewing Technical Alarms List72
- Viewing the Graphical Display of Technical Alarms (Alarm View)72
- Setting Alarm73
- Alarm Pause78
- Alarm Reset79
- Latching Alarms80
- Nurse Call81
- Intubation Status82
- Other Bed Alarm83
- Detecting Alarm84
- Actions When an Alarm Occurs85
Chapter 8 ECG86
- Introduction86
- Safety Information86
- ECG Display87
- Preparing for ECG Monitoring88
- ECG Settings94
- Arrhythmia Monitoring100
- ST Monitoring103
- Qt/Qtc Monitoring110
- Isoelectric Segments115
- ECG Relearning115
- Calibrating ECG115
- Defibrillation Synchronization116
- ECG Troubleshooting117
Chapter 9 Respiration Rate (RESP)119
- Introduction119
- Safety Information119
- RESP Display120
- RESP Settings122
- RESP Troubleshooting124
Chapter 10 Spo125
- Introduction125
- Safety Information125
- Spo Measurement Limitations126
- Spo Display127
- Spo Module129
- Monitoring Procedure129
- Setting Spo130
- Setting PR136
- Spo 2 Troubleshooting137
Chapter 11 Temperature（Temp139
- Introduction139
- TEMP Display139
- Preparing for TEMP Monitoring140
- TEMP Settings140
- TEMP Troubleshooting141
Chapter 12 NIBP143
- Introduction143
- Safety Information143
- NIBP Measurement Limitations145
- Measurement Modes145
- NIBP Display146
- Preparing for NIBP Measurements147
- Starting and Stopping NIBP Measurements148
- Viewing the Dynamic Blood Pressure Analysis149
- NIBP Settings149
- Assisting Venous Puncture152
- NIBP Maintenance152
- NIBP Troubleshooting153
Chapter 13 IBP154
- Introduction154
- Safety Information154
- IBP Measurement155
- IBP Display157
- Setting IBP158
- Calculating Cerebral Perfusion Pressure162
- IBP Troubleshooting162
Chapter 14 Carbon Dioxide (CO )164
- Introduction164
- Safety Information164
- CO Measurement Limitations165
- Monitoring Procedure165
- Display172
- Settings CO173
- Entering Intubation Status175
- Zeroing176
- Calibration177
- Exhaust Emission177
- Announcements178
- CO Troubleshooting179
Chapter 15 Review181
- Review Overview181
- Reviewing Page181
Chapter 16 Calculations191
- Introduction191
- Safety Information191
- Drug Calculation191
- Hemodynamic Calculations194
- Oxygenation Calculation196
- Ventilation Calculations199
- Nephridium Calculation201
Chapter 17 Other Functions204
- Analog Signal Output204
- Network Settings204
- Network Printing208
Chapter 18 Battery214
- Introduction214
- Installing a Battery214
- Charging the Bettery215
- Battery Guidelines215
- Battery Maintenance216
- Battery Recycling217
Chapter 19 Maintenance and Cleaning218
- Introduction218
- Cleaning the Monitor and Other Mounting Accessories219
- Disinfecting the Monitor and Other Mounting Accessories219
- Cleaning and Sterilizing of Accessories220
- Sterilization221
Chapter 20 Maintenance222
- Inspection222
- Maintenance Schedule223
- Checking the Version Information224
- Disposing of the Monitor224
Chapter 21 Accessories226
- Recommended Accessories227
Appendix A Product Specifications233
- Safety Specifications233
- Environmental Specifications234
- Physical Specifications234
- Power Specifications235
- Hardware Specifications236
- Data Storage239
- Wireless Network239
- Measurement Specifications240
- Alarm Specification258
Appendix B EMC and Radio Regulatory Compliance261
- Emc261
- The Management Compliance of Radio267
Appendix C Default Settings268
- ECG, Arrhythmia, ST and QT Default Settings268
- RESP Default Settings271
- Spo Default Settings271
- TEMP Default Settings272
- NIBP Default Settings273
- IBP Default Settings274
- CO Default Settings277
- Alarm Default Settings278
- Screen Setup Default Settings279
- Color of Parameters Default Settings279
- Other Default Settings279
- Maintenance Item Default Settings280
Appendix D Alarm Message281
- Physiological Alarm281
- Technical Alarm283
Appendix E Cybersecurity292
- Operating Environment292
- Network Data Interface292
- User Access Control Mechanism292
- Software Environment293
Appendix F Terminology and Definitions294
- List of Units294
- Symbol List295
- Terminology List296
Appendix G Toxic and Harmful Substances or Elements301

Biolight Meditech P1 - Page 53

Table of Contents