EasyManuals Logo

Cisco 7931G Administration Guide

Cisco 7931G
222 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #179 background imageLoading...
Page #179 background image
9-13
Cisco Unified IP Phone 7931G Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP and SIP)
OL-20798-01
Chapter 9 Troubleshooting and Maintenance
Resetting or Restoring the Cisco Unified IP Phone
Performing a Factory Reset
When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or
reset to its default value:
CTL file—Erased
LSC—Erased
User configuration settings—Reset to default values
Network configuration settings—Reset to default values
Call histories—Erased
Locale information—Reset to default values
Phone application—Erased (phone recovers by loading the term70.default.loads file or the
term71.default.loads file, depending on the phone model)
Before you perform a factory reset, ensure that the following conditions are met:
The phone must be on a DHCP-enabled network.
A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.
The term70.default.loads file or the term71.default.loads file and the files specified in that file
should be available on the TFTP server that is specified by the DHCP packet.
To perform a factory reset of a phone, perform the following steps:
Procedure
Step 1 Unplug the power cable from the phone and then plug it back in.
The phone begins its power up cycle.
Step 2 While the phone is powering up, and before the Speaker button flashes on and off, press and hold #.
Continue to hold # until each line button flashes on and off in sequence in amber.
Step 3 Release # and press 123456789*0#.
You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not
take place.
After you press these keys, the line buttons on the phone flash amber and then green, and the phone goes
through the factory reset process. This process can take several minutes.
Do not power down the phone until it completes the factory reset process and the main screen appears.

Table of Contents

Other manuals for Cisco 7931G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7931G and is the answer not in the manual?

Cisco 7931G Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Wall mountableYes
Electromagnetic compatibilityFCC Part 15 (CFR 47) Class B, ICES-003 Class B, EN55022 Class B, CISPR22 Class B, AS/NZS CISPR 22 Class B, CISPR 24, VCCI Class B, EN55024, EN 50082-1, EN 61000-3-2, EN 61000-3-3, EN 61000-6-1
Wi-FiNo
Networking standardsIEEE 802.1Q, IEEE 802.1af, IEEE 802.1p
Ethernet LAN interface typeFast Ethernet
Supported network protocolsDHCP, TFTP, CDP
Lines quantity24 lines
Phonebook capacity- entries
Number of VoIP accounts-
Voice codecsG.711a, G.729A, G.729B, G.729ab
Volume controlDigital
Display resolution192 x 64 pixels
Display number of lines3 lines
Display number of colorsMonochrome
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Safety(UL) 60950, (CSA) C22.2 No. 60950, EN 60950, IEC 60950, AS/NZS60950, TS 001
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth229 mm
Width203 mm
Height178 mm
Weight1360 g

Related product manuals