EasyManuals Logo

Cisco 7931G Administration Guide

Cisco 7931G
222 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #202 background imageLoading...
Page #202 background image
E-2
Cisco Unified IP Phone 7931G Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP and SIP)
OL-20798-01
Appendix E Basic Phone Administration Steps
Adding a User to Cisco Unified Communications Manager
Adding a User to Cisco Unified Communications Manager
This section describes steps for adding a user to Cisco Unified Communications Manager. Follow one
of the procedures in this section, depending on your operating system and the manner in which you are
adding the user:
Adding a User From an External LDAP Directory, page E-2
Adding a User Directly to Cisco Unified Communications Manager, page E-3
Adding a User From an External LDAP Directory
If you added a user to an LDAP Directory (a non-Cisco Unified Communications Server directory), you
can immediately synchronize that directory to the Cisco Unified Communications Manager on which
you are adding this same user and the user’s phone by following these steps:
Note Before you perform the following procedure, you must check the Enable Synchronizing from LDAP
Server check box in the LDAP System Configuration window of Cisco Unified Communications
Manager Administration (System > LDAP > LDAP System).
Procedure
Step 1 Log onto Cisco Unified Communications Manager Administration.
Step 2 Choose System > LDAP > LDAP Directory.
Step 3 Use the Find button to locate your LDAP directory.
Step 4 Click on the LDAP directory name.
Step 5 Click Perform Full Sync Now.
Note If you do not need to immediately synchronize the LDAP Directory to the Cisco Unified
Communications Manager, the LDAP Directory Synchronization Schedule on the LDAP
Directory window determines when the next auto-synchronization is scheduled. However, the
synchronization must occur before you can associate a new user to a device.
Step 6 Proceed to Configuring the Phone, page E-3.

Table of Contents

Other manuals for Cisco 7931G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7931G and is the answer not in the manual?

Cisco 7931G Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Wall mountableYes
Electromagnetic compatibilityFCC Part 15 (CFR 47) Class B, ICES-003 Class B, EN55022 Class B, CISPR22 Class B, AS/NZS CISPR 22 Class B, CISPR 24, VCCI Class B, EN55024, EN 50082-1, EN 61000-3-2, EN 61000-3-3, EN 61000-6-1
Wi-FiNo
Networking standardsIEEE 802.1Q, IEEE 802.1af, IEEE 802.1p
Ethernet LAN interface typeFast Ethernet
Supported network protocolsDHCP, TFTP, CDP
Lines quantity24 lines
Phonebook capacity- entries
Number of VoIP accounts-
Voice codecsG.711a, G.729A, G.729B, G.729ab
Volume controlDigital
Display resolution192 x 64 pixels
Display number of lines3 lines
Display number of colorsMonochrome
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Safety(UL) 60950, (CSA) C22.2 No. 60950, EN 60950, IEC 60950, AS/NZS60950, TS 001
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth229 mm
Width203 mm
Height178 mm
Weight1360 g

Related product manuals