EasyManua.ls Logo

DGSHAPE DWX-42W - Basic Operation Guide

DGSHAPE DWX-42W
169 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Contents
3
Company names and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2018 DGSHAPE Corporation
http://www.dgshape.com/
Thank you very much for purchasing this product.
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this
manual completely and store it in a safe location.
At the time of purchase, verify that the provided "Warranty" is a󰀩xed with the dealer's signature, address, and purchase date. Keep
this warranty in a safe location.
Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
The contents of this operation manual and the specications of this product are subject to change without notice.
The operation manual and the product have been prepared and tested as much as possible. If you nd any misprint or error, please
inform Roland DG Corporation.
DGSHAPE Corporation assumes no responsibility for any direct or indirect loss or damage which may occur through use of this
product, regardless of any failure to perform on the part of this product.
DGSHAPE Corporation assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any
article made using this product.
Error Message List ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������151
"1000-****" The % limit switch was not found� ���������������������������������������������������������������������������������������������������������������������152
"1006-02**" The % axis position has been shifted� �������������������������������������������������������������������������������������������������������������� 152
"101C-0000" The milling bur sensor was not found������������������������������������������������������������������������������������������������������������153
"101D-000*" The % milling bur cannot be released� ����������������������������������������������������������������������������������������������������������153
"101D-010*" The % milling bur cannot be released� It might be broken from the root� ���������������������������������������154
"101E-000*" The % milling bur might be broken� ����������������������������������������������������������������������������������������������������������������155
"101F-000*" The % milling bur chucking has slipped out� �����������������������������������������������������������������������������������������������156
"1020/1021-000*" The % milling bur is too long/too short� ���������������������������������������������������������������������������������������������157
"1022-000*" The % milling bur was not found ���������������������������������������������������������������������������������������������������������������������158
"1023-0000 to 1028-0000" Milling data error �����������������������������������������������������������������������������������������������������������������������159
"1029-0000" The spindle experienced an overload �����������������������������������������������������������������������������������������������������������160
"102A-000*" The spindle experienced overcurrent� ������������������������������������������������������������������������������������������������������������ 161
"102B-0000" The spindle motor temperature is too high� ������������������������������������������������������������������������������������������������ 162
"102E-0000" The mechanical part has collided� �������������������������������������������������������������������������������������������������������������������162
"1033-000*" The coolant has run out� ��������������������������������������������������������������������������������������������������������������������������������������163
"1034-0000" The coolant tank is not installed� ����������������������������������������������������������������������������������������������������������������������163
"1038-0000" Milling data error� No milling bur is selected� ����������������������������������������������������������������������������������������������165
"103A-000*" DANGER!! The coolant is leaking!! ��������������������������������������������������������������������������������������������������������������������165
"103B-0000" The automatic correction is not yet nished ����������������������������������������������������������������������������������������������166
"103D-0000" Milling data errorThe milling bur cannot reach the milling position� ����������������������������������������������166
"105E-0000" The pressure of the compressed air is too high or low ���������������������������������������������������������������������������� 167
"****-****" An unknown error occurred� ���������������������������������������������������������������������������������������������������������������������������������167

Table of Contents

Other manuals for DGSHAPE DWX-42W