Frick QUANTUM - Page 108

S90-010 O FRICK
®
QUANTUM™ COMPRESSOR CONTROL PANEL
Page 108 OPERATION
Aux. Failure............................................................. 93
Data Box ................................................................... 7
Interlock..................................................13, 40, 58, 80
Interlock Failure....................................................... 93
Interlock Setpoints................................................... 13
Manual Start............................................................ 11
Manual Stop............................................................ 11
Mode ... ....................................................6, 11, 83, 92
Model Differences ..............................9, 14, 81, 82, 92
Remote.................................................................... 11
Safeties ..............................................................14, 17
Safeties Setpoints ................................................... 22
Sequence Control.........................................13, 40, 80
Sequence Control (Mode 2) .................................... 54
Sequence Setpoints ................................................ 13
Sequencing ............................................................. 80
Start .…................................................................... 91
Starting Failure - Aux............................................... 93
Starting Failure - Low Motor Amps.......................... 93
Start-Up Procedure ................................................. 91
Status Box - Automatic.............................................. 7
Status Box - Manual.................................................. 7
Status Box - Remote ................................................. 7
Status Box - Mode..................................................... 7
Stop .… ..................................................................... 7
Stopping Failure - Aux............................................. 93
Stopping Failure - Motor Amps................................ 93
Stopping Procedure................................................. 91
Unable to Unload - Alarm........................................ 94
Condenser
Active Always.......................................................... 48
Ative Running.......................................................... 48
Analog Condenser Control...................................... 49
Control …………………………………………13, 40, 80
Analog.............................................................. 81
Digital............................................................... 81
Digital/Analog................................................... 81
Disable............................................................. 81
Setpoint............................................................ 47
Setpoints Lower Dead Band ............................ 48
Setpoints Lower Delay ..................................... 48
Response Time................................................ 48
Sequence Order............................................... 48
Upper Dead Band ............................................ 48
Upper Delay ..................................................... 48
Digital and Analog Condenser Control .................... 49
Digital Condenser Control ....................................... 48
Disabled .................................................................. 48
Not Active................................................................ 48
Off ..…..................................................................... 47
On ..…..................................................................... 47
Output . ................................................................... 48
#1 ............................................................. 48
#2 ............................................................. 48
#3 ............................................................. 48
#4 ............................................................. 48
Setpoints ................................................................. 13
Setup ...............................................14, 17, 39, 72, 91
Options Setup .................................................. 39
PID Setup......................................................... 39
Cycle Time setpoint........................................................ 19
D
DBS Alarm …….……………………………………………94
DBS Trip .… ................................................................... 94
Decrease ......................................................................6, 9
Decrease Slide Stop........................................................68
Delay ..……...............................................................33, 43
Detect I/O Boards............................................................79
Digital Board .............................................................83, 94
1 Comm. Fail - Shutdown.........................................94
2 Comm. Fail - Shutdown.........................................94
2 Module 1 Configuration.........................................83
2 Module 1 Config. - PLC control .............................83
2 Module 1 Config. - Ready to run ...........................83
Disable ..…........................................................................6
Discharge
Pressure ................8-10, 12, 18, 23, 33, 35, 47-49, 93
Pressure Sensor Fault .............................................94
Temperature......................................10, 21-23, 33, 94
Temperature Mode 2..........................................17, 18
Temperature Sensor Fault .......................................94
E
Electric – VFD .................................................................27
Enable .……......................................................................6
Engine .……....................................................................28
4–20 ma analog input...............................................28
4–20 ma analog output ............................................28
Confirmed Running (RPM).......................................29
Cycle Time...............................................................28
Drive Output at Max SV position ..............................28
Hardware Signals.....................................................28
High RPM ................................................................28
Alarm ................................................................28
Alarm Delay ......................................................28
Shutdown..........................................................28
Shutdown Delay................................................28
Idle Speed................................................................28
Low RPM ..........................................................28, 29
Alarm ................................................................29
Alarm Delay ......................................................29
Force Unload ....................................................28
Shutdown..........................................................29
Shutdown Delay................................................29
Stop Load..........................................................28
Manifold Pressure ....................................................28
Maximum output.......................................................28
Minimum output........................................................28
Rate of change.........................................................28
Setpoints..................................................................28
Slide Valve Position to begin Speed Increase..........28
Starting Maximum Delay..........................................29
Entering Process.................................................13, 22, 24
Disable ....................................................................82
Enable .....................................................................82
Safeties..............................................................22, 82
Temperature.......................................................13, 82
F
Factory Setpoints ............................................................31
False Start Failure - Aux..................................................94
False Start Failure - Motor Amps.....................................94
Fault History....................................................................31
Filter Diff. ..........................................................................9
Filter Pressure.................................................................35
High Filter Pressure Alarm.......................................35
High Filter Pressure Alarm Delay.............................35
High Filter Pressure Shutdown.................................35
High Filter Pressure Shutdown Delay ......................35
Overview of the Oil Pump Operation........................35
Setpoints............................................................34, 35